Contrôle d'accès

VERTX CS V100

Extrait Notice technique

70100

VertX? V100
Door/Reader Interface
Access Control Processing for Two Readers/Two Doors

The HID VertX products provide a complete and fully
featured hardware/firmware infrastructure for access
control software host systems. The V100 Door/Reader
interface connects two access control card readers via
Wiegand or Clock-and-Data interface controlling either
one or two doors. The V100 features on-board flash
memory, allowing program updates to be downloaded
via the network. The V100 connects to the V1000 through
a high speed RS-485 network. The V1000, in turn,
communicates with the system host via industry
standard TCP/IP protocol over 10/100 Mbps Ethernet or
the Internet. This architecture minimizes the impact on
corporate LANs by using only one TCP/IP address for
every 32 interfaces and by handling low-level
transactions on the RS-485 network.

Features

.55 mm)
4.825? (122

? Reports supervised inputs.
? Connects to the V1000 via RS-485.
? Receives and processes real time commands
from the V1000.
? Reports all activity to the V1000.
? Attractive polycarbonate enclosure protects
components from damage.
? All connections and indicators are fully
identified by silk-screened nomenclature on
the cover.
? Processes off-line access control decisions
based on facility code.
? UL 294 and UL 1076 recognized components.

5.8? (147.32 mm)

VertX? V100 2-Door Access Control Unit
Features

Specifications

Mounting
Mount to any wall surface, using four screws. For UL
compliance, one or more interfaces can be mounted
inside a locking customer-supplied NEMA-4 rated
enclosure with:
? DC supply with battery back-up
? Enclosure tamper switch
? All connections made through conduit
The unit should be installed indoors, inside a secure
area, such as in an IT or telecommunications room,
utility closet or on a wall above a suspended ceiling.

Dimensions

Visual Indicators
Communications LED flashes green for ?transmit to
host? and red for ?receive from host.? Power LED
indicates that sufficient DC voltage is being provided to
the unit.
Easily Interfaced
? Quick-disconnect screw terminal connectors
? Rotary address switch (0-15)
? Inputs for:
?
2 readers
?
2 door monitor switches,
?
2 Request-to-Exit switches
?
AC Fail Monitor*
?
Battery Fail Monitor*
?
Enclosure Tamper*
*Can be configured as a general purpose input
Non-latching relay outputs (rated 2 A @ 30 VDC):
? 2 door strikes (configurable)
? 2 auxiliary devices: door held/forced alarm,
alarm shunt, host off-line (comms down), or
general purpose
Local Processing
? Alarm shunt and strike relay timing and latching
functions
? Access control decisions based on facility code
(degraded mode)
? Basic input/output linking
? LED/beeper control during card + PIN, scheduled
unlock, and other transactions
Microcontroller
Warranty
Warranted against defects in materials and
workmanship for 18 months. (See complete warranty
policy for details.)
Part Numbers
Base Part Number: 70100

www.hidcorp.com
Specifications subject to change without notice.

5.8? W x 4.825? H x 1.275? D
(147.32 mm x 122.55 mm x 32.38 mm)
Weight: 12.4 oz (.35 kg)
Enclosure Material: UL94 Polycarbonate
Power Supply Requirements
60 mA @ 9-18 VDC (with no readers connected)
Recommended: Supervised linear power supply with
battery backup, input surge protection, and AC fail and
battery low contact outputs. When VertX is supplying
power to readers the requirements are 600 mA @ 9-18
VDC. The V100 can supply 500 mA to two readers.
Separate supervised DC supplies with battery back-up
recommended for door locking or relay activated devices,
or for HID MaxiProx readers.
Operating Environment
Indoors, or customer-supplied NEMA-4 rated enclosure
Temperature
32° to 122°F (0° to 50°C)
Humidity
5% to 95% relative, non-condensing
Communications Ports
RS-485 ? two wire. Two SIA standard Wiegand/Clock-andData ports
Certifications

UL 294 and UL 1076 Recognized Component for the US
CSA 205 for Canada
FCC Class A Verification
EMC for Canada, EU (CE Mark), Australia (C-Tick Mark),
New Zealand, Japan
EN 50130-4 Access Control Systems Immunity for the
EU (CE Mark)
Cable Distance
RS485 ? 4000 feet (1220 m) to host, using Belden 3105A,
22AWG twisted pair, shielded 100? cable
Wiegand ? 500 feet (150 m) to reader ? using ALPHA 1299C
22AWG, 9-conductor, stranded, overall shield (Fewer
conductors needed if all control lines are not used).
Input Circuits ? 500 feet (150 m), 2-conductor, shielded,
using ALPHA 1292C (22AWG) or Alpha 2421C (18AWG)
Output Circuits ? 500 feet (150 m), 2-conductor, using
ALPHA 1172C (22AWG) or Alpha 1897C (18AWG)
Minimum wire gauge depends on cable length and current
requirements.

CORPORATE HEADQUARTERS:
HID Corporation
9292 Jeronimo Road
Irvine, CA 92618-1905 U.S.A.
PHONE +1 (949) 598-1600 or (800) 237-7769
FAX +1 (949) 598-1690

HID INTERNATIONAL:
Asia Pacific: (852) 2530-9907
Europe: +44 (0) 1440 714 850

LITV100DSUS Rev. 12-04, ©2005 HID Corporation. All rights reserved.
HID, the HID logo, and VertX are trademarks or registered trademarks
of HID Corporation in the U.S., and/or other countries.