Contrôle d'accès

PROX ENTRYPROX

Extrait Notice installation Extrait Notice technique

ENTRYPROX 4045-905 (Rev C.0)

User'S GUIDE
HID Corporation
9292 Jeronimo Road
Irvine, California
92618 USA
Tel
949.598.1600
800.237.7769
Fax
949.598.1690
www.HIDCorp.com

ii

ENTRYPROX ? 4045-905 REV C.0

iii
Introduction ............................................. 1
Product Overview ................................... 2
Unit Capacity.........................................................2
Transactions .........................................................2
Specifications........................................................3
Default Settings.....................................................4

Installing EntryProx ................................ 4
Assembly Parts .....................................................4
Mounting the EntryProx Unit .................................6
Wiring the Controller Keypad for a
Standard Installation .............................................8
Wiring the Controller Keypad for a
Secure Installation ................................................9
UL 294 Compliance Requirements .....................14

Wiring EntryProx ................................... 17
Wiring the Main Relay .........................................18
Wiring the Auxiliary Relay ...................................18
Wiring the Request to Exit Input..........................19

Programming EntryProx....................... 20
Changing the Master Code .................................21
Card/PIN Programming Sequences....................25
Changing Operating Parameters ........................29
Downloading Data to a PDA ...............................33
Wiegand Mode....................................................40
Program Command Table...................................42
LED/Sounder Status ...........................................49

Appendix A: Users Chart...................... 51

HID CORPORATION

iv

ENTRYPROX ? 4045-905 REV C.0

1
INTRODUCTION
This User's Guide provides information and instructions for
installing, wiring, and programming the EntryProx unit.

IMPORTANT
?

?

?

?

?

YOU MUST KEEP A USER LIST when
programming cards and PIN codes into your EntryProx.
Write down the User Location, Card Number, PIN Code
and the Name of the User. Use the blank form in
Appendix A as a photocopy master.
YOU MUST CHANGE THE MASTER CODE from
the factory default (User Location 1, PIN Code: 1234) to
a new code (1-6 digits). Programming commands will
not work until the default Master Code is changed.
Write the new code down and keep it in a safe place.
PROGRAM THE NEW MASTER CODE INTO
LOCATION 0. Once this is done, the default Master
Code in User Location 1 can now be reprogrammed for
normal access control use. The Rev C EntryProx no
longer reserves User Location 1 for the Master Code.
IF YOU LOSE / FORGET THE MASTER CODE:
End Users: contact your dealer ?a service call is required.
Dealers: call HID Technical Support.
CONSIDER A SECURE INSTALLATION if
installing on an exterior door or high-risk location.

FCC WARNING - Changes or modifications not expressly
approved by the party responsible for compliance could void the
users' authority to operate this equipment. The reader is intended
to be powered from a limited power source output of a previously
certified power supply.
UL 294 COMPLIANCE - The EntryProx Unit complies
with UL 294 Standard for Access Control Units in a standard wallmount installation, only when installed in strict accordance with UL
requirements. Please refer to page 14 for details.
HID CORPORATION

2
PRODUCT OVERVIEW
The EntryProx unit provides card and keypad access control
for a single entrance. The unit can be installed in a standard
one-stage configuration or a secure two-stage (remote)
configuration. (Secure installation will be card-only.)
To gain access to the controlled door, the user presents their
card to the reader and / or enters their PIN code into the
keypad. The unit searches its memory for that card or PIN
code. If the unit finds the card or PIN code, it unlocks the
door or performs some other action that has been
programmed for that user.
The EntryProx unit is compatible with all HID proximity
access cards or key tags encoded with up to 37 bits of data.
All programming options are performed using the controller
keypad. Manual or batch card/tag programming via the
keypad can be completed for 26-bit format only. A batch of
cards or tags encoded in any format can be sequentially
presented to the reader by entering a single keypad command.
The Rev C EntryProx can download card and transaction
reports via the IR LED to an optional Palm PDA. Previous
product versions downloaded to a thermal printer.
UNIT CAPACITY

The EntryProx unit can accommodate up to 2,000 users.
Each user is assigned to a User Location (numbered 1 ?
2000), which can have a card/keytag, a PIN code, or a
card/keytag PLUS a PIN code. User Location 0 is reserved
for the Master Code (used for programming, only).
TRANSACTIONS

A maximum of 1,000 transactions can be stored in the
EntryProx unit. Each transaction includes the time, the date,
the User Location and the event. When maximum capacity is
reached, the oldest transactions are overwritten.
ENTRYPROX ? 4045-905 REV C.0

3
PRE-PROGRAMMING THE UNIT
BEFORE INSTALLATION
Dealers and installers are advised to pre-program the unit at
their offices before installing it at the site. Simply connect it
to a 12VDC source, follow configuration and card enrollment
instructions at the end of this guide, and disconnect the unit.
Programming will be retained in memory. You will spend
less time at the site, and by being familiar with programming,
will be able to train the end user more effectively.
SPECIFICATIONS
TABLE 1 - SPECIFICATIONS

CATEGORY

Environmental
Operating
Temperature
Operating Humidity
Electrical
Power
Supply/Current
Requirements

Mechanical
Height
Width
Depth
Relay Outputs
Main Relay, Aux Relay
Sounder
LEDs

HID CORPORATION

REQUIREMENTS

?31F to +150F
(-35C to +66C) @ 30 VDC
5% to 95% relative humidity,
non-condensing
10 - 15V DC, linear, filtered
and regulated power supply
recommended 150 mA for the EntryProx
unit only.
Additional capacity or separate supply
required for locking device or peripherals.
5.25 in (13.3 cm)
2.75 in (7 cm)
1.625 in (4.1 cm)
Form C (switches up to 1A inductive
load, 2A resistive @ 30VDC)
4000 Hz, defeatable
Bi-Color (red/green)
Amber
Infrared

4
DEFAULT SETTINGS

The EntryProx unit is shipped with the following default
settings.
PARA
PARAMETER

DEFAULT SETTING

Master Code (User Location 1)
Code must be changed before
programming the unit.
Main Relay energizes for
Audible Keypress Feedback
Local Propped Door Sounder
activates after
Local Forced Door Sounder
activates immediately for
Data Output Port

1234*
5 seconds
ON
30 seconds
10 seconds
Infrared (IR) port

METER DEFAULT SETTING

INSTALLING ENTRYPROX
You can install the EntryProx unit by using a standard
installation method or a secure installation method. Both
installation methods require that you mount the EntryProx
unit to a wall or glass surface.
ASSEMBLY PARTS

Before you install the EntryProx, be sure that you have the
correct factory and installer supplied parts.
A. Controller Keypad Unit
B. Controller Keypad Backplate
C. Cable Assemblies
D. Antenna Backplate
E. Antenna Housing
F. Blank Label
G. Mounting Screws

I. Silicone Rubber Cushion
J. Self-Adhering Pads
K. 2-pin Jumper ?
L. Filler Piece
M. Lithium ?Coin Cell?
Battery (see warning below)*
N. Cover screws ? hex and
tamper.*
O. Hex wrench*

H. Press to Exit Label
* - not shown in Figure 1
? - pre-installed on main board connector P2, pins 5 & 6

ENTRYPROX ? 4045-905 REV C.0

5
FIGURE 1: FACTORY SUPPLIED PARTS

A

K
L
H

I
B

J
G

F
D

E

C

INSTALLER SUPPLIED PARTS LIST

? Appropriate DC power supply (10-15VDC, linear type)
? Appropriate separate power supply for door locking unit.
? Appropriate electrical tools
? Recommended remote antenna cable ALPHA 1294C
(22AWG)
? Wiegand interface cable ALPHA 1295C (22AWG) (only if
using a separate Wiegand access control panel)
? Power supply cable (18AWG - 22AWG)
? Door locking unit cable (18AWG - 22AWG)
? Door monitor cable (18AWG - 22AWG)
? Request to Exit cable (ALPHA 2421C 18AWG or ALPHA
1292C 22AWG) (only if using remote switch)
? Optional tamper screw bit (only if tamper screw is used)
? Ademco 945T or PR-20451 magnet and reed switch or
equivalent (for UL 294 compliance)

HID CORPORATION

6
CAUTION ? Replace Battery with Panasonic BR1225 only.
Use of another battery may present a risk of fire or explosion.
Battery may explode if mistreated.
Do not recharge,
disassemble or dispose of battery in fire.

MOUNTING THE ENTRYPROX UNIT
If you mount the EntryProx unit to a wall, you can install an
electrical junction box to hold the unit and the wires in place.
The mounting hole cutouts on the backplate line up with the
screw holes on a standard junction box.
If you mount the EntryProx unit to a glass surface, DO NOT
remove the wire exits on the backplate. Remove the
appropriate wire exit cutouts located on each side of the
controller keypad case.
If your installation must comply with the UL 294 Standard
for Access Control, please read Page 14.
PRECAUTIONS FOR OUTDOOR INSTALLATIONS

Water damage is a key cause of unit malfunction, causing
corrosion or short circuits. When mounting the unit in an
area that will be exposed to rain or moisture, take the
following precautionary measures:
1. Use silicone to seal wire runs and mounting holes
(antenna is already sealed).
2. Do NOT seal the cover and base together. Water
that enters the case must be allowed to run out at the
bottom.
3. Bend the wires to form a drip loop before they
enter the case. This will prevent water from following
the wires into the case.

ENTRYPROX ? 4045-905 REV C.0

7
BEGINNING ENTRYPROX INSTALLATION

To mount the EntryProx unit, refer to Figures 2 and 3 and
follow these instructions:
1. Remove the hex screw located at the bottom of the
EntryProx unit.
2. Disconnect the backplate of the EntryProx unit
from the controller keypad.
3. Remove the wire exits and mounting hole cutouts
from the backplate as shown in Fig. 2.
4. Pull the wires through the backplate as shown in
Figure 3.
5. Attach the backplate to a wall or glass surface using
the mounting screws or the self-adhesive fasteners.
FIGURE 2: REMOVING THE WIRING EXITS AND MOUNTING HOLES

Mounting Hole
Cutouts
Wire Exits

Mounting Hole
Cutouts

FIGURE 3: PULLING THE WIRES THROUGH THE BACKPLATE

HID CORPORATION

8
WIRING THE CONTROLLER KEYPAD FOR A
STANDARD INSTALLATION

In a standard installation, the antenna housing remains
installed in the controller keypad, and the complete unit is
installed outside of the secured area. This is appropriate for
interior doors or ?low-risk? exterior installations.
For compliance with the UL294 Standard, additional installation
requirements must be met ? see page 14.

To wire the EntryProx unit for a standard installation, refer
to Figure 4 and follow these instructions.
1. Touch a grounded object BEFORE touching the
main circuit board to guard against possible static
discharges.
2. Remove the main circuit board by pushing outward
on the two spring tabs in the direction shown in
Figure 4.
3. Lift the main circuit board.
4. Make the wiring connections for the door locking
devices, the power supply, and the alarm inputs and
outputs. Refer to the ?Wiring EntryProx? section for
appropriate wiring diagrams.
5. Reattach the main circuit board to the controller
keypad unit.
6. Attach the controller keypad unit to the mounted
backplate and secure the EntryProx unit with a hex
screw or tamper screw.
Note: A ribbon cable holds the main circuit board to the
controller keypad board. DO NOT CUT OR REMOVE this
cable from its connector.

ENTRYPROX ? 4045-905 REV C.0

9
FIGURE 4: REMOVING THE CIRCUIT BOARD

WIRING THE CONTROLLER KEYPAD FOR A SECURE
INSTALLATION

In a secure installation, the waterproof antenna housing is
removed from the controller keypad and mounted outside of
a secured area. The control unit is installed inside the secured
area. The blank filler piece is then inserted into the controller
keypad in its place. This is appropriate for exterior doors
or ?medium to high-risk? locations.
To wire the EntryProx unit for a secure installation, refer to
Figures 5 and 6 and follow these instructions.
1. Touch a grounded object BEFORE touching the
main circuit board to guard against possible static
discharges.

HID CORPORATION

10
2. Remove the main circuit board by pushing outward
on the two spring tabs in the direction shown in
Figure 4.
3. Lift the main circuit board.
4. Unplug the four-pin cable assembly from
connector P4 on the main circuit board.
5. Release the antenna housing from the controller
keypad by pressing inward on the four securing tabs.
6. Remove the antenna housing from the controller
keypad by pushing forward as shown in Figure 6.
7. Insert the extra 10-inch antenna cable assembly
into connector P4.
8. Splice in additional antenna cable Alpha 1174C
(22AWG) up to a maximum of 10 feet.
Note: The Alpha 1174C antenna cable is not supplied with the
EntryProx unit.

9. Make the wiring connections for the Request to
Exit switch, the door locking devices, the power
supply, and the alarm inputs and outputs. Refer to the
?Wiring EntryProx? section for appropriate wiring
instructions.
10. Reattach the main circuit board to the controller
keypad unit.
11. Insert the blank filler piece into the controller
keypad unit.
12. Attach the controller keypad unit to the mounted
backplate and secure the EntryProx unit with a hex
screw or tamper screw.
13. Run the additional antenna cable to the antenna
housing location.
14. Mount and wire the antenna housing

ENTRYPROX ? 4045-905 REV C.0

11
FIGURE 5: REMOVING THE P4 CONNECTOR

P4 Connector
Cable Assembly

FIGURE 6: REMOVING THE ANTENNA HOUSING

HID CORPORATION

12
MOUNTING AND WIRING THE ANTENNA HOUSING
FOR A SECURE INSTALLATION

Mount and wire the antenna housing no more than 10 feet
away from the controller keypad unit.
To mount and wire the antenna housing, refer to Figures 7
and 8 and follow these instructions.
1. Pull the additional antenna cable through the
antenna housing's backplate cable holes.
FIGURE 7: MOUNTING THE ANTENNA BACKPLATE

Cable Holes

Moisture Release
Holes

2. Position and secure the antenna backplate to the
mounting surface so that the two moisture release
holes are on the bottom.
3. Cut the plastic connector off the antenna cable
assembly.
4. Splice in the additional antenna cable. Be careful to
match the wire colors to the proper pin connectors
on the 10-inch antenna cable assembly.
5. Attach the antenna housing to the backplate by
inserting the four securing tabs into the backplate.
6. Seal the wire holes with silicone.

ENTRYPROX ? 4045-905 REV C.0

13
SELECTING A FILLER OR REQUEST TO EXIT LABEL

The filler piece replaces the antenna housing on the controller
keypad when you use the high security installation. If you do
not plan to use the filler piece as a Request to Exit switch:
1. Insert the filler piece into the opening on the
controller keypad.
2. Apply the blank label.
FIGURE 8: ATTACHING THE ANTENNA HOUSING

If you plan to use the filler piece as a Request to Exit switch:
1. Remove the two plastic side tabs on the filler piece.
2. Insert the silicone rubber cushion over the two
alignment pins on the switch activator.
3. Apply the ?Press to Exit? label to the filler piece.
4. Insert the filler piece into the opening on the
controller keypad.
5. Refer to Figure 11 to make the wiring connections
to the cable assembly if you are using a door contact.
6. Set the internal Request to Exit button ON, using
programming Command 30, option 7 (see Table 2).

HID CORPORATION

14
FIGURE 9: USING THE FILLER PIECE AS A REQUEST TO EXIT SWITCH

Cushion

Side Tab

INSTALLATION REQUIREMENTS FOR UL
294 COMPLIANCE
The EntryProx Model 4045CGNU0 complies with the
UL294 Standard for access control units in a standard, wallmount installation, when installed to the following
specifications:
?

Electric locking mechanisms may only be connected to
the NO contacts of the Main Relay. Locking devices
requiring an NC connection may only be used in
conjunction with an interposing relay mounted inside the
secure area and connected to the NO contacts of the
Main Relay.

?

The recommended or equivalent shielded wiring must be
used for the following applications:
ENTRYPROX ? 4045-905 REV C.0

15
Request to Exit input
cable
Wiegand data output cable
Antenna cable extension

?

Alpha 1292C (22AWG) or
2421C (18AWG)
Alpha 1295C (22AWG)
Alpha 1294C (22AWG)

The cable shield drain wires must be grounded at the
reader end by connection to P1, Pin 4 (DC Power
configurations recommended below) by connection to
P1, Pin 4 (DC Power Ground) using appropriate wire
nuts or crimp fittings.
Tamper Switch must be installed in one of the
configurations recommended below,and connected to an
intrusion alarm system. (Refer to Figure 10 for
switch/magnet locations)

MOUNTING OVER A METAL OR PLASTIC SINGLE
GANG J-BOX

1. Use an Ademco 945T magnet and reed switch (or
equivalent) with foam-backed adhesive tape.
2. Clip the screw mounting tabs from both the magnet
and reed switch using pliers or a wire cutter.
3. Remove the backing sheet from the tape on the
magnet and stick the magnet to the plastic spacer,
which is factory-installed to the back of the Keypad
board in location A (Figure 10).
4. Stick the reed switch on the inside of the long side of
the J-box in the upper right-hand corner, using the
adhesive tape. The switch should be flush with the
edge of the J-box.
WALL MOUNTING

1. Use an Ademco PR-20451 magnet and reed switch
(or equivalent) with foam-backed adhesive tape.
2. Remove the backing sheet from the tape on the
magnet and stick the tape to the plastic spacer,
HID CORPORATION

16
which is factory-installed to the back of the Keypad
board at location B (Figure 10).
3. Drill a 3/8 inch hole in the wall behind the magnet
location, feed the switch wire through the wall and
press the switch into place.

FIGURE 10 ? TAMPER SWITCH INSTALLATION

Magnet
M agnetB B

Magnet A
M agnet A
Keypad
Keypad Electronics Board
Electronics Board

Batt.
Batt.

Main
Board
Main Electronics
Electronics Board

NOTE: UNIT IS SHOWN FROM BACK WITH BASE REMOVED

ENTRYPROX ? 4045-905 REV C.0

17
WIRING ENTRYPROX
Figure 11 illustrates the location and description of the four
pin connectors on the main circuit board and its use.
Connector P5 is not used.
FIGURE 11: PIN LOCATOR DIAGRAM

Blue ? Not Used
Brown ? Wiegand LED Control
White ? Wiegand Data 1
Green ? Wiegand Data 0

Red ? Power +12 VDC
Black ? Ground
Blue ? Main Relay COM
Green ? Main Relay NO
Gray ? Main Relay NC

* Note: Rex Loop requires NO
switch; Door Loop requires NC
switch. Connect commons from
both loops to Loop Common input
P2, Pin 6, White.

HID CORPORATION

Green ? Aux Relay NO
Gray ? Aux Relay NC
Blue ? Aux Relay COM
Brown ? Rex Loop
Orange ? Door Loop
White ? Loop Common*

Red ? LED (Red +)
Black ? LED (Green +)
Antenna +
Antenna -

18
WIRING THE MAIN RELAY

The main relay for the door locking device is wired to
connector P1 on the EntryProx main circuit board.
WIRING A GATE ACTUATOR

You can make the wire connections for a gate actuator by
connecting the Blue (C) wire and the Green (N/O) wire
directly to the input.
Note: DO NOT connect a power supply to the relay if
you connect a gate actuator.
WIRING THE AUXILIARY RELAY

The EntryProx unit has an auxiliary relay feature that allows
for customized alarm programming. Pins 1, 2, and 3 on the
P2 connector can be wired for one of the following alarm
outputs:
? Alarm shunt
? Forced or propped door
The alarm shunt operation allows you to use the auxiliary
relay to bypass a door contact that is monitored by a separate
alarm system. If the entry or exit is controlled by the
EntryProx unit, an intrusion alarm will not be generated if the
door is opened using an access card or PIN number, or by
pressing the REX button.
The forced or propped door alarm allows you to use the
auxiliary relay to provide a local warning, such as an audible
or visual indicator if:
? A door is opened without using an access card or PIN
number at the EntryProx unit.
? A door is legitimately opened but is held open too long.
Note: The auxiliary relay audible and visual indicators and
the door open times can be programmed. Refer to Table 2:
Programming Commands for more information.

ENTRYPROX ? 4045-905 REV C.0

19
WIRING THE REQUEST TO EXIT INPUT

When the EntryProx Request to Exit (REX) input receives a
momentary switch closure, it engages the main relay for the
programmed access time. It can be connected to a wallmounted exit button, to a push button under a reception
desk, or to the relay output of a passive infrared motion
detector mounted above the door on the secure side. The
Request to Exit input activates the alarm shunt to prevent
false alarms when personnel use the controlled door to exit
the secured area. The Transaction Log records all Request to
Exit usages for monitoring purposes.
Locate connector P2 on the main circuit board and remove
the 2-pin jumper installed on pins 5 and 6.
Note: If you do not use a door contact, you need to twist the
white and orange wires together or the REX input will not
function properly.

.
Note: The door contact must be closed for the Request to
Exit feature to work properly

HID CORPORATION

20
PROGRAMMING ENTRYPROX
IMPORTANT ? READ BEFORE
PROGRAMMING THE ENTRYPROX UNIT
YOU MUST KEEP A USER LIST when programming
cards and PIN codes into your EntryProx. Write down the
User Location, Card Number, PIN Code and the Name of
the User. Use the blank form at the end of this book as a
photocopy master. You will need this information if you
need to delete a card or PIN at a later time.
NEW FEATURE on Rev C Model ? USER
LOCATION 0 RESERVED FOR MASTER CODE.
This feature was added to reduce service calls due to
overwritten Master Codes. The Master Code places the unit
into programming mode. The master code defaults to User
Location 1, but after a Master Code is programmed into
Location 0, User Location 1 can be reprogrammed as any
User Type.
NEW FEATURE on Rev C Model - FORCED
CHANGE TO MASTER CODE This feature was added
to increase security. The Master Code must be changed
from the factory default, before any programming can be
done. Write the new code down and keep it in a safe place.
IF YOU LOSE OR FORGET THE MASTER CODE:
End Users: contact your dealer ?a service call is required.
Dealers: call HID for the procedure ? and remember to bring
the proper hex key or security tool to the customer site!

ENTRYPROX ? 4045-905 REV C.0

21
PROGRAMMING COMMAND SEQUENCES

Command sequences are simply a series of keypad entries to
add cards and PINs or change operating characteristics of the
EntryProx unit. There are three basic steps to programming
EntryProx, using the Keypad on the control unit:
1-Place the unit in programming mode
press 99 # Master Code *
2- Enter a Command Sequence
press a 2-digit command number to enter
cards/PINs or specify parameters by pressing
keys in various sequences
3- Exit programming mode - press * to exit.
LED INDICATION DURING PROGRAM MODE

A slow blinking yellow LED indicates that the unit is in
program mode.
When the yellow LED stops blinking and is OFF completely,
the unit is no longer in program mode.
A steady yellow LED indicates an error condition:
1- you are trying to enter a card or PIN which is already
stored in another User Location
2- you have pressed the wrong key in a command
sequence
Press * to clear the error condition, then enter a new code or
PIN, or re-enter the command sequence as required. If the
unit does not go into program mode, contact your dealer or
HID Technical Support.
CHANGING THE MASTER CODE

The EntryProx cannot be programmed before you change
the master code. This feature prevents users from leaving the
default code in the unit; thereby preventing unauthorized
programming and tampering. The steps are:
1. Enter programming mode using the default master
code in User Location 1. Press: 99 # 1234 *

HID CORPORATION

22
2. Enter a new master code into User Location 0. Press:
50 # 1 # 0000 # new master code * new master
code * (Code can be 1 ? 6 digits. This PIN is

mirrored into User Location 1)
3. Enter a new code into User Location 1. See
CARD/PIN PROGRAMMING SEQUENCES.
4. Press * to exit program mode.
You can now program any user type into User Location 1, or
you can simply delete it. User Location 0 is not an access
code ? it is only used to enter programming mode. Although
it is not recommended, you can also program the same PIN
used in User Location 0 as an access code in another location
? it is the only code not checked for duplication.
It is also possible to change the master code and leave the
master code in user location 1, however, this is not
recommended, because the master code can be accidentally
overwritten.
BEFORE YOU START?
Before programming cards, try to determine:
?
How many cards do I have to enroll? If you have
more than 50-75, you may want to batch enroll them. If
you have fewer, you may want to program one at a time.
?

How are the cards encoded: What is the bit format,
ID numbers and facility code? If you have sequentially
numbered cards with 26-bit format and the same facility
code, you can batch-enroll them from the keypad.
Otherwise you must program them individually or batchenroll by sequentially placing the cards in front of the
reader. Note that if you choose to add new 26-bit
cards manually (via the keypad), the facility code
must be entered into the unit first. For the
programming sequence used to enter the 3-digit facility
code, see Table 2, item 32.
ENTRYPROX ? 4045-905 REV C.0

23
PIN CODE/CARD PROGRAMMING BASICS
PIN codes and card numbers can be programmed manually
via the keypad. Cards can also be programmed by
presentation to the reader at the correct point in the
command sequence.
When adding or modifying PIN codes or cards, the user
enters a 2-digit Command, then specifies three or four data
values: a user type, a location, and a keypad-PIN and/or
card.
USER LOCATIONS

These are the locations in the unit's memory where Card
and/or PIN User data is stored. EntryProx User Locations
are numbered 1 ? 2000. User Location 0 is reserved for the
Master Code, used for programming ? Cards or PINs for
normal access cannot be entered into User Location 0.
USER TYPES

User Types determine what happens when a user presents
their card/PIN to the reader. A User Location can be
programmed as one of four specific user types:

Toggle latch strike (0) For this user-type, when the Card is
presented (or PIN is entered) the door opens for an indefinite
period, until the card / code is reentered or another toggle
code is entered (this is useful for deliveries, for example).
Normal access (1) This is the default user type, when the

Card is presented (or PIN is entered) the door opens for the
duration of the Main Relay time.

Download Log (2) For this user-type, when the Card is
presented (or PIN is entered) the door remains locked and
the Transaction Log is ?Downloaded? to an optional Palm
PDA via the IR LED. (There are three LEDs on the top of
HID CORPORATION

24
the unit - the IR LED is the one on the right.) This code
cannot be used to gain access through the door. Note that the
log is only downloaded and displayed, not erased.

Lockout (3) For this user-type, the keypad ?freezes,?
disallowing all other codes, plus the door remains in the
current state. During a lockout state, card access does not
continue to work. If it is locked, it remains locked. If it is
unlocked, it remains unlocked until another Lockout code is
entered, releasing it from Lockout mode. NOTE: Reserve
this user-type for a supervisor or override function.
PIN CODES, CARDS AND COMBINATIONS

A User Location can be programmed with one of the four
PIN code/card combinations listed below using the
programming Commands in parentheses
(1) PIN Code ONLY (Command 50)
(2) PIN Code AND Card (Command 50 plus present
card to proximity reader)
(3) Card ONLY (Command 50 or Command 51)
(4) PIN Code OR Card (Command 52)
No User Location can have the same card and/or access PIN
code as another User Location.
ENTERING USER PIN CODES

EntryProx user PIN codes consist of a minimum of one digit
and a maximum of six digits. Note that a leading ?0? is
considered a digit, and that the 5-digit code 12345 is different
from the six-digit code 012345. Attempting to enter a user
PIN code into memory that is already stored in a different
user location causes the yellow LED to stop blinking and
remain steadily lit. If this occurs, try entering a different user
code. Repeating digits in the same code is acceptable (ex:
121122).

ENTRYPROX ? 4045-905 REV C.0

25
CARD/PIN PROGRAMMING SEQUENCES
Following are the most commonly used command sequences
for programming user data into the EntryProx:
PROGRAMMING PIN + CARD

To program a user for both Code AND Card:
1. Place the EntryProx unit in program mode. Press:
99 # Master Code *

2. On the EntryProx keypad, press:
50 # user-type # user location # keypad PIN
* keypad PIN *

3. Press * to exit program mode.
Here is an example, assuming a master code of 2468 and
programming user 2 with PIN 1111
Press 99#2468*
Press 50#1#2#1111*1111*

Press *
Remember to write an entry in your user list:
?User:2 Type:1 PIN:1111 Card:0056 Name: John Doe ?
QUICK PROGRAMMING EITHER PINS OR CARDS

A ?quick program? feature allows user data entry with
minimal keystrokes. No command number is required. This
feature programs either a card or a PIN, not a combination,
and it automatically selects a ?Normal? user access type. Just
enter the user's location and the PIN (or present card):
1. Place the EntryProx unit in program mode. Press:
99 # Master Code *

2. On the EntryProx keypad, for Code Quick Enroll
press: user location # PIN * PIN * OR for Card
Quick Enroll press: user location # **
3. Press * to exit program mode.

0-Toggle

USER TYPES - REMINDER
1-Normal
2-Download
3-Lockout

HID CORPORATION

26
PROGRAMMING PIN CODE ONLY USE

To program PIN Code ONLY operation with Command 50,
use the following program sequence:
1. Place the EntryProx unit in program mode. Press:
99 # Master Code *

2. On the EntryProx keypad, press:
50 # user-type # user location # keypad PIN
* keypad PIN *

3. Press * to exit program mode.
PROGRAMMING CARD ONLY USE

To program Card ONLY use with Command 50, simply omit
the keypad PIN values from the sequence:
1. Place the EntryProx unit in program mode. Press:
99 # Master Code *

2. On the EntryProx keypad, press:
50 # user-type # user location # **


3. Press * to exit program mode.
PROGRAMMING CODE OR CARD

To program a user for either Code OR Card:
1. Place the EntryProx unit in program mode. Press:
99 # Master Code *

2. On the EntryProx keypad, press:
52 # user-type # user location # keypad PIN
* keypad PIN *

3. Press * to exit program mode.
BATCH LOAD CARDS BY KEYPAD ENTRY

Command 56 allows you to batch load multiple, sequential
26-bit HID cards into the EntryProx unit. Up to 2000 users
can be added at one time. Cards need not be presented to the
reader. Requirements are:
?
Cards must all have the same facility code.
?
Cards must be sequentially numbered
?
The facility code must be programmed into the
unit before any batch loading. See Table 2,
ENTRYPROX ? 4045-905 REV C.0

27
Command 32 for the procedure. (This facility
code cannot be changed at a later time).
Cards with multiple facility codes or many numbering gaps
must be entered by presentation to the reader, using
Command 53.
If the Batch Loading conditions can be met:
1. Place the EntryProx unit in program mode. Press:
99 # Master Code *

2. On the EntryProx keypad, press:
56 # (total number of cards to be added) #
(starting user location) # card number *
repeat card number *

3.Press * to exit program mode.
.
BATCH LOAD BY PRESENTATION

Use Command 53 to program a batch of cards into
consecutive User Locations by specifying the starting User
Location, then presenting cards or tags to the reader. Use
any card format up to 37 bits. All cards are programmed
alike and users are ?card only.? Card enrollment stops once
the current user location exceeds 2000, or if you press any key
to abort. Keep a written record as you program cards.
Existing data in the User Locations being programmed is
overwritten, unless you present a card that is already
programmed into the EntryProx, in which case an error is
generated. To clear the error, press the * key; then continue
presenting cards.
To batch load by presentation, follow this procedure:
1. Place the EntryProx unit in program mode. Press:
99 # Master Code *

0-Toggle

USER TYPES - REMINDER
1-Normal
2-Download
3-Lockout

HID CORPORATION

28
2. On the EntryProx keypad, press:
53 # user type # start location # **
?
3. Press * to exit program mode.
DELETING USERS

To delete a user from the EntryProx, you must know the
User Location in which the information is stored.
1. Place the EntryProx unit in program mode. Press:
99 # Master Code *

2. On the EntryProx keypad, press:
user location #**

3. Press * to exit program mode.
BLOCK DELETE USERS

Use Command 58 to delete all cards / PINs in a block of
User Locations. The yellow LED will blink rapidly during
the deletion process. It can take several seconds to delete
large blocks of users. (Entering a starting user location or
number of locations which exceeds 2000 will generate a
programming error.)
To block delete user locations, follow these steps:
1. Place the EntryProx unit in program mode. Press:
99 # Master Code *

2. On the EntryProx keypad, press:
58 # start location # start location # number of
locations * number of locations*

3. Press * to exit program mode

ENTRYPROX ? 4045-905 REV C.0

29
CHANGING OPERATING PARAMETERS
Many users will use the EntryProx with the factory default
operating parameters. The following commands include
some of the most commonly customized parameters. For
further refinements on EntryProx operation, review the
options shown in Table 2.
CHANGING THE MAIN RELAY TIME - The main relay

time applies to all users 1-2000. The factory default main relay
time is five (5) seconds. Main relay time can be set from one
to ninety-nine seconds in one-second increments using
Command 11.
1. Place the EntryProx unit in program mode. Press:
99 # Master Code *

2. Enter the new main relay time, in seconds (from 1
to 99). For example, to enter 10 seconds, press:
11 # 10 # 0 # **

3. Press * to exit program mode.
INVALID PIN LOCKOUT - Command 30, Option 18 allows

you to enable or disable the Invalid PIN Lockout (IPL)
feature. This feature prevents unauthorized persons from
gaining entry by guessing PIN codes or Master Codes. When
a preset number of invalid entries is exceeded (set by using
Command 32 ? option 4, default is 5) the EntryProx will
either trigger the Forced Door output, or the keypad will be
disabled for a user-configurable time period (select the action,
using Command 30, option 19, and then set lockout time by
using Command 32 ? 5).
The invalid PIN code count is reset to zero by any of the
following:
Entering a valid keypad PIN
Presenting a programmed Prox card
Entering a valid [99 # Master code*] sequence
The expiration of the keypad timer
HID CORPORATION

30
The Invalid PIN Lockout function disables all keypad PIN
entries with the exception of the [99 # Master Code*]
sequence for the duration of the lockout.
To clear an active timed Invalid PIN Lockout do any of the
following:
?
Disconnect power to the system
?
Present a valid prox card programmed as ?Card Only? or
?Card OR Code?
?
Enter the [99 # Master Code *] sequence
Note that if an invalid [99# Master Code*] is entered as part
of the sequence to clear the IPL, a subsequent good [99#
Master Code*] sequence will not cancel the current lockout.
RESETTING THE MASTER CODE AND
SYSTEM DEFAULTS ONLY

Command 40 erases everything from the EntryProx memory
except the user list and transaction log and restores the
default settings. This is useful if the EntryProx unit has
experienced programming problems, or if you wish to delete
earlier programming.
When you do this command the following rules apply:
- If user #0 has not been programmed and user #1 is
programmed then user #0 is erased and user #1 is set to
default (1234).
- If user #0 has been programmed and user #1 has not been
modified, user #0 and user #1 are set to default data (1234).
- If user #0 has been programmed and user #1 has been
modified, user #0 is set to default (1234) and user #1 is not
changed.

ENTRYPROX ? 4045-905 REV C.0

31
Please note that you must change the master code after
performing this command.
1. Place the EntryProx unit in program mode. Press:
99 # Master Code *

2. Press:
40 # 00000 # 00000 # **

3. Press * to exit program mode.
ERASING ENTIRE MEMORY / RESETTING
SYSTEM DEFAULTS

Command 46 deletes everything from the EntryProx memory
including the user list but not the transaction log and
restores the default settings. This is used as a last resort if you
need to erase a specific user and could not retrieve the
Programmed User List. After performing this command
the master code must be reprogrammed.
1. Place the EntryProx unit in program mode. Press:
99 # Master Code *

2. Press:
46 # 00000 # 00000 # **

3. Press * to exit program mode.
TURNING KEYPRESS AUDIBLE
FEEDBACK ON/OFF

The Keypress Audible Feedback command enables the
sounder to beep once for each key press. This feature
provides an audible acknowledgment that a particular key was
pressed hard enough for the unit to understand. The factoryshipped default setting is ON, but it can be toggled ON and
OFF as desired using command 30.
1. Place the EntryProx unit in program mode. Press:
99 # Master Code *

2. To enable this feature, press:
30 # 0 # 1 # **

3. To disable this feature, press:
30 # 0 # 0 # **

4. Press * to exit program mode.
HID CORPORATION

32
TURNING KEYPRESS VISUAL FEEDBACK ON/OFF

The keypress visual feedback feature lights the LED once for
each key press. This feature provides a visual
acknowledgment that a particular key was pressed hard
enough for the unit to understand. The factory-shipped
default setting is ON, but it can be toggled ON and OFF as
desired.
1. Place the EntryProx unit in program mode. Press:
99 # Master Code *

2. To enable this feature, press:
30 # 1 # 1 # **

3. To disable this feature, press:
30 # 1 # 0 # **

4. Press * to exit program mode.
AUTO ENTRY ENABLE

This function is not recommended for use, as it lowers
the overall security of the unit and affects programming
sequences ending with the * key. It is set with the 30#
command (Set/Clear Standard Options). When this feature
is enabled, any PIN code the same length as the master code
does not require the * key. Leave this feature in the default
mode, which is OFF.

ENTRYPROX ? 4045-905 REV C.0

33
DOWNLOADING DATA TO A PDA
The EntryProx unit can download a Transaction Log and a
Programmed User List to an optional Palm Personal Digital
Assistant (PDA) via the IR LED. There are three LEDs on
the top of the EntryProx unit - the IR LED is the one on the
right.
USING THE DCD PROGRAM
The Data Collection Device (DCD) Application is provided
as a free download on the HID Website (go to
http://www.hidcorp/downloads/entryproxdcd). The DCD
application is downloaded to a PC, and is then downloaded
to the Palm via the cradle or IR interface. Download
instructions and a list of compatible Palm models are shown
on the website. Refer to the Palm user documentation for
instructions on how to operate the Palm PDA, how to install
programs, and for the location of the Palm IR Receiver.
1. Touch the Data Collection icon on the PDA screen.
2. The program will start, displaying three menu
options: Retrieve, Files, and Settings

HID CORPORATION

34
3. Click on Settings to be sure the following parameters
are selected:
a. Comm Method ? Ir Channel 2
b. Comm Speed ? 19200
c. Protocol ? Printer
d. Timeout (Seconds) ? 30

4. To download data from the EntryProx Unit to the
Palm:
a. Touch Retrieve on the PDA screen
b. Place the Palm IR receiver within 1/2? of the
EntryProx IR LED (to the right of the yellow
LED)
c. Enter the required command sequence at the
EntryProx keypad
You have 30 seconds to enter the command sequence
after entering the receive screen. If the data begins to
send before you press Retrieve, then you will miss the
beginning of the data.
5. Command sequences are described in detail in the
following sections.
SELECTING TRANSACTION LOG INFORMATION

You can selectively program specific transaction events to be
included (or not) on the Transaction Log. By ?masking? out
certain events, you direct the unit not to save those events in
memory and thus they do not appear in the log. The factory
ENTRYPROX ? 4045-905 REV C.0

35
default is for all transaction events to be saved in memory
and included in the log. The procedure follows:
1. Place the EntryProx unit in program mode. Press:
99 # Master Code *

2. To turn OFF an event (keep it from being
stored/logged), enter:
73 # Event Code # 0 # **

To turn an event ON, enter:
73 # Event Code # 1 # **

3. Press * to exit program mode.
The Event Code is a two-digit number that represents
a specific transaction as listed in the following table.
The following transaction events can be set/cleared
(saved/not saved) and therefore downloaded/not
downloaded.
EVENT CODE

TRANSACTION EVENT

01
02
04
05
06
07
10
12
16
17
20
21
24
25
27

Access Denied
Program Denied
REX (Request to Exit)
Door Ajar
Door Closed
Forced Door
Error Lockout Activated
Facility Code Access
Download (to PDA)
Access
TGL ON (Toggle ON)
TGL OFF (Toggle OFF)
Lo ON (Lockout ON)
Lo OFF (Lockout OFF)
MSMTCH (Mismatch on Card
and Code entry)
Program mode started
Log erased

29
30

HID CORPORATION

36
DOWNLOADING A TRANSACTION LOG
Using the optional Palm PDA with the DCD Program, you
can download and display a Transaction Log via the
EntryProx IR port. Transaction Logs can be downloaded
using two different methods, (1) by programming a card or
code to ?Download? the transaction log to the PDA and (2)
by placing the EntryProx unit into program mode and
manually entering the Display Transaction Log command.
PROGRAMMING A CARD OR CODE TO INITIATE
A TRANSACTION LOG REPORT ?DOWNLOAD?

1. Place the EntryProx unit in program mode. Press:
99 # Master Code *

2. For a CODE DOWNLOAD, press:
50 # 2 # user location # code * code *

For a CARD DOWNLOAD, press:
50 # 2 # user location # **

and then present the card at the proximity reader.
3. Press * to exit program mode.
NOTE: Entering the programmed PIN code or
presenting the card subsequently causes the unit to
download a Transaction Log to the optional PDA.
DOWNLOADING A TRANSACTION LOG MANUALLY

1. Place the EntryProx unit in program mode. Press:
99 # Master Code *

2. Touch Retrieve on the PDA screen
3. Place the Palm IR receiver within 1/2? of the
EntryProx IR LED (to the right of the yellow
LED)
4. Then, on the EntryProx, press 70 # 0 # 0 # **
The PDA will display a progress bar while collecting
the data, and when done will display End of Dump
(download). You can touch Close/Stop on the PDA
or wait for the unit to time out.

ENTRYPROX ? 4045-905 REV C.0

37
When prompted for a Session Name, you can place
your stylus on the line containing the date
information and add to it or replace it with descriptive
text.
3. Press * to exit program mode.
The 70 command is logged in the transaction buffer
(in memory), providing a reference as to when
the log was downloaded. Figure 12 shows a sample
Transaction Log.
FIGURE 12 - TRANSACTION LOG

The Palm PDA will store reports after they are
downloaded. To view a stored report, touch Files, select a
report from the list and click on Action. The drop-down
menu selections are Info, View and Remove.
HID CORPORATION

38
Info gives the time and date the report was recorded.
Remove allows you to delete the report. View displays the
report. The top line of the screen shows the current line
and total number of lines as you scroll or page up and down
through the report.
Here is a description of the report layout:
Top line ? Current Line/Total Lines
Second line ? Session Data
Transaction lines: Time, Date, User Location, Action
TIME - 24-hour format
Date: mm/dd/yyyy
User Location (0-2000)
ACTION describes each event
ERASING A TRANSACTION LOG

The Transaction Log should be erased from memory in the
EntryProx after being downloaded to prevent conflicting
logs. To erase the log, enter the following sequence:
1. Place the EntryProx unit in program mode. Press:
99 # Master Code *

2. To erase the transaction log press:
76 # 00000 # 00000 # **

3. Press * to exit program mode.
DOWNLOADING A PROGRAMMED USERS LIST

The Programmed Users List can be downloaded to the
optional Palm PDA via the unit's IR LED. The list identifies
the user location for each user's data. It also displays user
locations that are not programmed, so to avoid an
unnecessarily long file, the download can be stopped when a
sufficient percentage of records have been processed. The
percentage of records downloaded is continually updated
during the download process.
1. Place the EntryProx unit in program mode. Press:
99 # Master Code *
2. Touch Retrieve on the PDA

ENTRYPROX ? 4045-905 REV C.0

39
3. Hold the optional PDA up to the EntryProx
IR port steadily (about ½ inch away; the IR port is
located to the right of the yellow LED)
4. Then, on the EntryProx, press 25 # 0 # 0 # **
The PDA will display a progress bar while collecting
the data (Retrieving users %) and when done will
display End of Dump (download). You can touch
Close/Stop on the PDA or wait for the unit to time
out. When prompted for a Session Name, you can
place your stylus on the line containing the date
information and add to it or replace it with descriptive
text.
3. When the list is complete, press * to exit program
mode.
FIGURE 13 - PROGRAMMED USER LIST

Here is a description of the Report Layout:
Top line ? Title
Second line ? Session Data
Column 1 ? User location
Column 2 ? user type (see table)
Column 3 ? PIN CODE
Column 4 - SITE CODE/CARD NUMBER.

HID CORPORATION

40
WIEGAND MODE
If you program the EntryProx unit to operate in Wiegand
mode with a separate access control panel, the following
features are not accessible:
? The EntryProx unit does not control door lock or
unlocking operations.
? The EntryProx unit is not able to store codes in memory.
? The main and auxiliary relay functions are turned off.
? The door monitor and Request to Exit inputs are disabled.
For more information on programming the EntryProx unit
for Wiegand operation, please contact your local distributor.
PIN CODE OUTPUT IN WIEGAND MODE

The system transmits keypad PINs while operating in
Wiegand mode by processing any digit sequence terminated
with the [*] key as 26-bit Wiegand data. The current facility
code (set using Code 32 - 2) will be used. Entering any PIN
over 65535 will cause an error condition and no data will be
sent.
Because keypad data is sent in a card data format, it may not
be possible for some panels to perform CARD AND CODE
operation (requiring both) to gain access. If your panel cannot
accept and interpret 26-bit format as PIN data, be sure to
configure the user at the PC host software by entering the
code into the CARD data field for that user, not the keypad
PIN number field.
LED CONTROL OPTIONS FOR WIEGAND MODE
The combined programming for Options 30#9 ? 30#12 and
the Wiegand LED Control line affect the LED display in
Wiegand mode. The table below shows how the LED will
behave when the LED control line is open (normal) or
grounded (asserted by the access control panel).
ENTRYPROX ? 4045-905 REV C.0

41
G = Green, R = Red, Y = Yellow. See the following
section for more on option programming.
Opt 9
Opt 10
Opt 11
Opt 12
Led Ctl Open
Led Ctl Gnd

HID CORPORATION

0 0
- 0 1
- 0
G

0
1
1
G

1
0
0
-

1
0
1
0

1
0
1
1
G
R Y R

1
1
0
R

1
1
1
0
R
G

1
1
1
1
Y

42
PROGRAMMING COMMAND TABLE
Read the following table before completing programming of
your EntryProx unit; it describes various programming
commands and how to execute them. As with the previously
described commands, you must first press 99 # (Master
Code) * to enter programming mode, enter the desired
command sequence, and then press * to exit programming
mode. ?Ref? number is for reference only, not to provide an
ordered sequence of commands.
TABLE 2: PROGRAMMING COMMANDS.

TO...
Ref IF YOU WANT TO

PRESS

DETAILS

1

Enter program
mode

99 # (Master
Code) *

yellow LED
blinks slowly

2

Program new
master code into
user location 0

50 # 1 # 0000 #
master code *
master code *

example: 4321
master code
(50 # 1 # 0000 #
4321 * 4321 *)

3

Set main relay time

11 # tt # 0 # **

4

Set AUX relay
output

15 # output mode
# 0 # **

5

Delete users

User Location #
**

6

Download a
transaction
Log

70 # 0 # 0 # **

tt = 1 - 99
seconds
Output Modes:
0 = disabled,
1 = shunt,
2 = forced door,
3 = propped
door
Example:
To delete user
100, press:
100#**
Hold optional
Palm PDA
IR receiver near
the EntryProx IR
LED.

ENTRYPROX ? 4045-905 REV C.0

43
Ref

IF YOU WANT TO

PRESS

DETAILS

7

Set/clear standard
option

30 # option # s/c
# **

See below for
Option
numbers and
descriptions

ESS DETAILS

Option Number/Description
0: Audio keypress feature
1: Visual keypress feature
2: Auto entry enable
3: Stand-alone/Wiegand operation
4: Facility code access (26-bit
cards only). Note: this disables the
?toggle? card function.
5: Forced door audio alert
6: Propped door audio alert
7: Internal Request to Exit switch
8: US/EU Daylight Savings
rollover dates.
9: Wiegand red LED enable
10: Wiegand red LED active state
11: Wiegand green LED enable
12: Wiegand green LED active
13: Automatic Daylight Savings
Time change
14: Prox card antipassback select
18: Invalid PIN lockout select
19: Invalid PIN lockout action

HID CORPORATION

Set/Clear
0 = OFF/1 = ON
0 = OFF/1 = ON
0 = OFF/1 = ON
(Recommend OFF)
0 = standalone/1=Wiegand
0 = OFF/1 = ON
0 = OFF/ 1 = ON
0 = OFF/1 = ON
0 = OFF/1 = ON
0 = US/1 = European
0 = OFF/1 = ON
0 = LOW/1 = HIGH
0 = OFF/ 1 = ON
0 = LOW/1 = HIGH
0 = OFF/ 1 = ON
0 = OFF / 1= ON (prevents
multiple card reads in
Wiegand mode)
0 = OFF / 1= ON
0 = TIMED LOCKOUT / 1
= Forced Door Output

44
Ref

IF YOU WANT TO

PRESS

8

Download
programmed
user list

25 # 0 # 0# **

DETAILS

Hold optional Palm
PDA IR receiver near
the EntryProx IR
LED.
9
Download
25 # 0 # start
Hold optional Palm
programmed
user # **
PDA IR receiver near
user list (starting at
the EntryProx IR
a certain user)
LED.
10
Change Wiegand
32 # parameter Parameter/Value
& Miscellaneous
# value # **
0, Wiegand pulse
parameters
width, default=8,
160µs, (1=20µs),
range= 1- 255
1, Wiegand interpulse
spacing, default=32,
640µs, (1=20µs),
range=1-255
2, facility code/0-225
(default = 1) (26-bit
cards only) verify!
3, Process card timer
2 ? 240 in ¼ second
increments, defaults
to 4 ? 1 second??
4, Invalid PIN
lockout threshold 1 ?
50 attempts (defaults
to 5)
5, Invalid PIN
lockout duration 1 ?
255 in 5 second
increments (defaults
to 60 - 5 minutes)
?? If Option 30# 14# is enabled, this sets the time that a card must
be removed from the RF field before it can be re-read. If option
30#14# is disabled, this sets the time between successive readouts,
used in either standalone or Wiegand mode.

ENTRYPROX ? 4045-905 REV C.0

45
Ref

IF YOU WANT TO

PRESS

11

Set system time

12

Set system date

13

Set door number

14

Set propped door
time (this sets
delay time for
both the Aux
Relay and local
sounder)
Set forced door
time (this sets
active time for
both the Aux
Relay and local
sounder)
Delete memory
except user list
and restore
system defaults
(also see
command 46)
Delete all
memory and reset
system defaults
Program user:
Code ONLY

41 # hhmm # 0 hhmm =
# **
hour/minute,
24-hr format
42 # mmddyy
mmddyy =
month, day, year;
# dow # **
dow = day of week,
1 = Sunday
43 # nnnn # 0
nnnn = door number
# **
(for downloaded
reports)
44 # ttt # 0 #
ttt = propped door
**
time, to nearest 10's
seconds, entered
as 10 -990; default =
30 seconds

15

16

17
18

NOTE: You can
program the four types of
users shown to the right

HID CORPORATION

45 # ttt # 0 #
**

DETAILS

ttt = forced door
time, to nearest 10's
seconds, entered
as 10 - 990; default =
10 seconds

40 # 00000 #
00000 # **

46 # 00000 #
00000 # **
50 # user-type
# user location
# code * repeat
code *

User Types:
0 - Toggle/latch strike
1 - Normal Access
2 - Log Download
3 - Lockout

46
Ref

IF YOU WANT
TO

PRESS

19

Program user:
Code AND
Card

20

Program user:
Card ONLY

20A

Program new
master code
into user
location 0
Program card
user
manually: Card
ONLY (26-bit
cards ONLY)

50 # user-type
# user location
# code * repeat
code *

50 # user-type
# user location
#**

50 # 1 # 0000 #
master code *
master code *

21

22

Program user:
Code OR Card

23

Program a
group of
consecutive
users by
presenting cards

51 # user-type
# user location
# card ID * card
ID *
52 # user-type
# user location
# code* repeat
code *

53 # user type #
start location #
**



?

DETAILS

the card ID appears
on the card (facility
code must be entered
first; see 32 # 2 #
command)

Programs card-only
users. Stops at user
location 2000, or
press any key to
abort. Erases existing
programming. If an
existing card is
presented, an error
will occur ? press * to
resume

ENTRYPROX ? 4045-905 REV C.0

47
Ref

IF YOU WANT TO

PRESS

DETAILS

24

Perform batch
entry of users:
Card
ONLY (26-bit
cards ONLY)

the card ID appears
on the card; (facility
code must be entered
first; see 32 # 2 #
command)

25

Block Delete
Users

56 # total count
# starting user
location #
starting card ID
* starting
card ID *
58 # start user
# start user #
number of users
* number of
users *

26

Quick Enroll
Card

27

Download
Transaction
Log via IR port

28

Set transaction log
mask (set/clear
event logging)

NED ORS

HID CORPORATION

User Location
# * *
70 # 0 # 0 # **

73 # event #
set/ clear # **

Yellow LED blinks
rapidly; allow several
seconds for large
blocks of users.
Cannot delete: master
user, more than 2000
users, or user
location greater than
2000.

Hold optional Palm
PDA IR receiver near
the EntryProx IR
LED.
Prevent specified
transactions from
being logged. Set =0
(prevent)
Clear = 1(restore)
See list below.

48
Code ? Transaction Event
01 ? Access Denied
02 ? Program Denied
04 ? Request to Exit
05 ? Door Ajar
06 ? Door Closed
07 ? Forced Door
10 ? Invalid PIN Lockout
12 ? Facility Code Access
16 ? Download to PDA
17 ? Access
20 ? Toggle ON
21 ? Toggle OFF
24 ? Lockout ON
25 ? Lockout OFF
27 ? Mismatch
29 ? Program Mode started
30 ? Log erased
29
30

IF YOU WANT TO

EntryProx? HID
Le lecteur autonome

4045

Application
En proposant une technologie de proximité pour le contrôle
d'accès à une porte unique, l'EntryProx? est la solution
idéale, aussi bien pour les petites installations que pour les
entrées éloignées dans le cadre d'un système global.
Cet appareil esthétique et résistant peut aisément être
transformé en un lecteur mode Wiegand, que vous pouvez
alors connecter à tout type de contrôleur.

Caractéristiques
?
?
?

?
?

?

?
?

Enregistre jusqu'à 2000 utilisateurs et 1000
événements horodatés.
Compatible avec toutes les cartes et porte-clés de
proximité HID.
Son module antenne amovible peut être déporté
jusqu'à 3 m de l'unité de contrôle, aussi bien à
l'extérieur qu'à l'intérieur.
Enregistrement par lots des cartes au format 26 bits.
Muni d'un clavier à 12 touches permettant la saisie
d'un code d'identification personnelle (PIN) ou la
programmation.
Impression des événements par liaison infrarouge
sur une imprimante portative optionnelle (veuillez
consulter votre agence HID).
Lorsqu'une porte est "entrouverte" et/ou "forcée", un
relais déclenche une alarme.
Muni d'un bouton de Demande de Sortie (DDS).

Le lecteur autonome EntryProx? HID
Spécifications techniques
Distance de lecture maximale*
Carte ProxCard® II : jusqu'à 7,5 cm (3.0")
Carte ISOProx® II : jusqu'à 6,25 cm (2.5")
Carte DuoProx ® II : jusqu'à 6,25 cm (2.5")
Porte-clés ProxKey? II : jusqu'à 3,7 cm (1.5")
Carte ProxCard® Plus : jusqu'à 2,5 cm (1.0")
*En fonction des conditions d'installation sur site
Dimensions
13,33 x 6,98 x 3,49 cm (5.25" x 2.75" x 1.375")

Configuration type de l'unité de contrôle

Tension d'alimentation / Consommation
10 - 15 V cc, protection contre les inversions de tension
Alimentation linéaire recommandée, 150 mA - 12 V cc
Sorties relais
Relais gâche commun commutant jusqu'à 4A - 30 V cc
Relais auxiliaire commun commutant jusqu'à 1A - 30 V cc
Entrées de contrôle
Position de la porte - contact normalement fermé
Demande de Sortie (DDS) - contact normalement ouvert
Signal sonore
4000 Hz, peut être désactivé
LEDs
Bicolores (rouge/vert), orange, infrarouge (pour une utilisation
avec une imprimante portable optionnelle de format calculette,
veuillez consulter votre agence HID)
Température de fonctionnement
De -30°C à 65°C (-22 °F à 150°F)

Module antenne déporté de l'unité de contrôle

A.

Humidité de fonctionnement
Humidité relative de 5% à 95% sans condensation
Distance de câblage
Module antenne déporté : 3 m
Interface Wiegand : 152 m
Câble recommandé : ALPHA 1295C à 5 conducteurs,
22AWG (American Wire Gauge), totalement blindé
ou câble équivalent
Fonctionnement
Temps de déclenchement : 1 - 99 secondes (paramétrable)
Mode de déclenchement : horloge d'accès ou bascule
électronique
Durée d'ouverture de la porte : 10 - 990 secondes (paramétrable)

B.
Numéros de référence des accessoires
(veuillez consulter votre agence HID)
A. Imprimante
4045-PRN
B. Outil de sécurité
04-0001-03
C. Papier pour imprimante
4045-RFL
(ne figure pas sur l'illustration).
9292 Jeronimo Road
Irvine, CA 92618-1905 U.S.A.
Tél. : +1 (949) 598-1600
+1 (800) 237-7769
Fax. : +1 (949) 598-1690
HID France
35, Bd de la Victoire
F-67000 STRASBOURG
Tél. : +33 (0)3 90 22 10 66
Fax. : +33 (0)3 88 36 64 45
Imprimé aux U.S.A.

Programmation des cartes
Format 26 bits - enregistrement des cartes par lots
Format propriétaire - enregistrement carte par carte
Options de traitement du code site (26 bits exclusivement)
Vérification du code site et du numéro d'identification de la carte
Vérification du code site uniquement (accepte tous les numéros
d'identification (ID#))
Homologations
FCC - en cours
Marquage CE - en cours

Numéros de référence
EntryProx
4045AGN00
EntryProx livré avec 10 porte-clés
4045AGK00
EntryProx livré avec 20 ProxCard II 4045AGC00
(Veuillez vous reporter au guide de commande HID pour la
description des options disponibles ainsi que pour les numéros
de référence correspondants).
LIT4045DS 12/99, remplace la version 6/99

www.HIDCorp.com

Les spécifications techniques sont susceptibles d'être modifiées sans notification préalable.

©1999 HID Corporation