Contrôle d'accès

PROX MAXIPROX

Extrait Notice installation Extrait Notice technique

Installation Manual - 5375-901 Rev D
MaxiProx DFM Reader 5375A

HID Corporation, 9292 Jeronimo Road, Irvine, CA 92618-1905, USA ? Tel: (949) 598-1600, (800) 237-7769, Fax: (949) 598-1690
http://www.hidcorp.com
MaxiProx DFM Reader Installation Manual 5375-901 Rev D
Page 1 of 20

CONTENTS
CHAPTER 1
1.1
1.2
1.3

OPERATION....................................................................................................................................................................................... 5
PARTS LIST ........................................................................................................................................................................................ 5
REGULATORY A PPROVALS AND CERTIFICATIONS.................................................................................................................... 5

CHAPTER 2
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
2.12
2.13
2.14
2.15
2.16
2.17

INSTALLATION PROCEDURE.......................................................................................................................................6

PREPARATION .................................................................................................................................................................................. 6
M OUNTING AND INSTALLATION .................................................................................................................................................. 6
M OUNTING A PPLICATIONS........................................................................................................................................................... 6
CABLE PREPARATION ..................................................................................................................................................................... 6
INSTALL CABLE................................................................................................................................................................................ 6
CABLE NOTES................................................................................................................................................................................... 6
CABLE CONNECTIONS..................................................................................................................................................................... 7
DIP SWITCH AND JUMPER SETTINGS ........................................................................................................................................... 8
TAMPER SWITCH ............................................................................................................................................................................. 9
M OUNTING........................................................................................................................................................................................ 9
POWER SUPPLY .............................................................................................................................................................................. 10
A UTOTUNE OPERATION .............................................................................................................................................................. 10
READER TESTING........................................................................................................................................................................... 10
POWER-UP TUNE ........................................................................................................................................................................... 10
PERIODIC A UTOTUNE ................................................................................................................................................................... 10
SUPERVISOR M ODE........................................................................................................................................................................ 10
INSTALL COVER.............................................................................................................................................................................. 10

CHAPTER 3
3.1
3.2
3.3
3.4

MAXIPROX SYSTEM OVERVIEW ................................................................................................................................5

INSTALLATION NOTES AND GUIDELINES.............................................................................................................13

POWER SUPPLY .............................................................................................................................................................................. 13
INSTALLATION NEAR M ETAL ..................................................................................................................................................... 13
RADIO FREQUENCY INTERFERENCE ........................................................................................................................................... 13
TRANSPONDER TYPES................................................................................................................................................................... 14

CHAPTER 4

APPLICATION NOTES...................................................................................................................................................15

4.1
W IEGAND INTERFACE DESCRIPTION ......................................................................................................................................... 15
4.1.1
Wiegand Message Format.................................................................................................................................................. 15
4.1.2
Output Specification ........................................................................................................................................................... 15
4.1.3
Signal Levels ........................................................................................................................................................................ 16
4.1.4
Data Pulses........................................................................................................................................................................... 16
4.1.5
Example Output ................................................................................................................................................................... 16
4.2
CLOCK AND DATA INTERFACE DESCRIPTION.......................................................................................................................... 17
4.2.1
Clock and Data Message Format..................................................................................................................................... 17
4.2.2
Data Timing.......................................................................................................................................................................... 17
4.2.3
Output signal Levels ........................................................................................................................................................... 18
4.2.4
Bit structure.......................................................................................................................................................................... 18
4.2.5
Bit Stream.............................................................................................................................................................................. 19
4.2.6
Output Specification ........................................................................................................................................................... 20
4.3
RS232 AND RS422 CARD M ESSAGE SPECIFICATION (SEND M ODE ONLY).......................................................................... 20

HID Corporation, 9292 Jeronimo Road, Irvine, CA 92618-1905, USA ? Tel: (949) 598-1600, (800) 237-7769, Fax: (949) 598-1690
http://www.hidcorp.com
MaxiProx DFM Reader Installation Manual 5375-901 Rev D
Page 2 of 20

FIGURES
FIGURE 1:
FIGURE 2:
FIGURE 3:
FIGURE 4:

M AXIPROX FRONT VIEW ............................................................................................................................................................ 11
M AXIPROX INTERIOR VIEW SHOWING MOUNTING HOLE LOCATIONS............................................................................... 12
DATA PULSES - TIMING PARAMETERS ..................................................................................................................................... 16
DATA TIMING - TIMING CHART ................................................................................................................................................ 18

HID Corporation, 9292 Jeronimo Road, Irvine, CA 92618-1905, USA ? Tel: (949) 598-1600, (800) 237-7769, Fax: (949) 598-1690
http://www.hidcorp.com
MaxiProx DFM Reader Installation Manual 5375-901 Rev D
Page 3 of 20

TABLES
TABLE 1:
TABLE 2:
TABLE 3:
TABLE 4:
TABLE 5:
TABLE 6:
TABLE 7:
TABLE 8:
TABLE 9:

TB1 CONNECTOR DEFINITION...................................................................................................................................................... 7
TB2 CONNECTOR DEFINITION...................................................................................................................................................... 7
DIPSWITCH AND JUMPER SETTINGS........................................................................................................................................... 8
INTERFACE JUMPERS DESCRIPTION - P3 AND P4 ...................................................................................................................... 8
SWITCH DESCRIPTION - SW2 ....................................................................................................................................................... 8
M ODE CHART .................................................................................................................................................................................. 8
BAUD RATE CHART ? RS232 AND RS422.................................................................................................................................... 8
SWITCH DESCRIPTION - SW5 ....................................................................................................................................................... 9
LOGIC LEVELS................................................................................................................................................................................. 16

HID Corporation, 9292 Jeronimo Road, Irvine, CA 92618-1905, USA ? Tel: (949) 598-1600, (800) 237-7769, Fax: (949) 598-1690
http://www.hidcorp.com
MaxiProx DFM Reader Installation Manual 5375-901 Rev D
Page 4 of 20

Chapter 1 MaxiProx System Overview
The MaxiProx Reader is a self-contained proximity Reader. The two piece polycarbonate enclosure has
an O-ring that weather seals the enclosure pieces together and a cable fitting that seals the cable entry.
The water-resistant unit is designed for outdoor use. The enclosure is mountable on a single gang
electrical box. A bi-color LED and audible tone provide user feedback. Configurable open collector data
outputs provide the data to the Host. Configurable DIPswitches and jumpers provide choice of data
interfaces between Wiegand, Clock and Data, RS 232 and RS422. The data interface is configured as
ordered from the factory, but can be changed in the field - please contact HID Technical Support for
assistance. A tamper switch can alert the Host when the enclosure is opened. Internal DIP switches
and jumpers provide for configuration of the outputs, audible tone and LED control options.
Installation of the MaxiProx Reader consists of mounting, connecting the cable to the Host and
+12VDC or +24VDC power, verifying the DIPswitch and jumper settings, verifying Autotune, and
verifying the reading of a transponder.

1.1 Operation
Transponders (Proximity Cards or ProxKeys) are presented to the front of the MaxiProx. The LED is red
when ready to read a transponder. The LED turns green and the beeper sounds when the tra nsponder
is read and the message is transmitted to the Host computer or interface panel. The system is ready for
another transponder as soon as the LED returns to red. There is an anti-passback delay of about one
and a half seconds before it will read the same card. The LED flash is typically 250 milliseconds long.
The operation of the LED and beeper may be controlled by the Host, in which case the actual operation
will depend on the programmed timing of the Host.

1.2 Parts List
MaxiProx Reader

Qty 1 (included)

2.

Installation Manual

Qty 1 (included)

3.

Cable Fitting

Qty 1 (included)

4.

Label for front cover - HID logo

Qty 1 (included)

5.

#6-32 x 1" flat head screw, for upper-left base mount
screw

Qty 1 (included)

6.

#6-32 x 1" black screw, for gang-box mounting

Qty 2 (included)

7.

#6-32 x .75" flat head screw, for front cover mounting

Qty 1 (included)

8.

Cable, 5 conductor, 22 AWG (Alpha 1295 C or
equivalent)

See cable notes

1.

9.

Power Supply ? 2.0 A linear regulated

10.

+12VDC Shunt Jumper ? P2-1 to P2-2 for 12VDC
operation

+24VDC, nominal (+21 TO 28.5VDC)
Factory Default ? No P2 Shunt Jumper
For Europe, use ALTRONIX SMP3
(USER SUPPLIED TRANSFORMER AND
BATTERY)
+12VDC, nominal (+11.6 to +20.9VDC)
For Europe , use ALTRONIX SMP3
(USER SUPPLIED TRANSFORMER AND
BATTERY)

1.3 Regulatory Approvals and Certifications
§

Underwriters Laborites listing

§

CE Mark

HID Corporation, 9292 Jeronimo Road, Irvine, CA 92618-1905, USA ? Tel: (949) 598-1600, (800) 237-7769, Fax: (949) 598-1690
http://www.hidcorp.com
MaxiProx DFM Reader Installation Manual 5375-901 Rev D
Page 5 of 20

§

FCC Certification

§ Foreign
Approvals

Countries

EMC

and/or

Type

§

European Declaration of Conformity

§

Pacemaker wearers should exercise
caution when in close proximity to this
product.

Chapter 2 Installation Procedure
2.1 Preparation
Determine an appropriate mounting position for the MaxiProx. Install an electrical box or drill the
appropriate mounting holes from inside the base with the cover removed for #6 fasteners. For optimum
performance, the Reader should be mounted at least 4 inches away from any metallic surface 12-inch x
12-inch or larger. The Autotune feature automatically compensates for incidental metal such as
aluminum studs and conduit. The best method for installing the MaxiProx is by mounting the back of
the Reader to the mounting surface. Side mounting is usually accomplished with an adapter or spacer
(customer supplied) that mounts to the back of the Reader.

2.2 Mounting and Installation
§

When fastening the MaxiProx to the mounting surface, do not use a metallic fastener larger than a #6 screw.

§

Avoid mounting the MaxiProx closer than 1 meter (40-inches) to another MaxiProx.

2.3 Mounting Applications
§

The MaxiProx may be mounted to a gooseneck that is 1½-inch in diameter with a 4-inch diameter-mounting flange without
degradation of read range. The flange should be mounted to a non-metallic adapter that will ease the installation of the
MaxiProx to the flange. The read range will not be affected.

§

The MaxiProx may be mounted to a 12-inch x 12-inch or larger metal plate with a 4-inch spacer used to separate the Reader
from the plate.

§

Acrylic, Plexiglas, Lexan (polycarbonate) or other suitable plastics may be found in ½-inch to 1-inch stock. Mounting
adapters may be fabricated from these materials that would be sturdy and not affect the performance of the MaxiProx.
Plastic J-boxes can also be used.

2.4 Cable Preparation
Prepare the cable by cutting the cable jacket back 2 inches and strip the wires 1/4-inch. Tinning the
wires is not required.

2.5 Install Cable
Route the interface cable from the MaxiProx to the Host. Connect the MaxiProx DC power input to the
Host or external power supply. Either +12VDC or +24VDC can be used.

CAUTION!
The shunt jumper P2 is not installed as the factory default for +24VDC operation. If the jumper is in the
+12 VDC position and +21 to +28.5 VDC is applied, circuit damage can result.

2.6 Cable Notes
§

For Wiegand interface cable the maximum length is 500 feet (150m), 50 feet (15m) for RS232, and 4000 feet (1200m) for RS422.
HID Corporation, 9292 Jeronimo Road, Irvine, CA 92618-1905, USA ? Tel: (949) 598-1600, (800) 237-7769, Fax: (949) 598-1690
http://www.hidcorp.com
MaxiProx DFM Reader Installation Manual 5375-901 Rev D
Page 6 of 20

§

When using 5 conductor cable, the power supply and Host must have a common ground (voltage reference).

§

7-Conductor cable is required when using the Hold function or if the ground for the MaxiProx's power supply is not
common with the ground of the Host. TB2 terminal 3, Data Return, is to be connected to the ground of the Host. (Alpha
1296 C or equivalent).

§

7-Conductor cable is required when the Hold function is used, and the power supply and Host "ground" are separate.
(Alpha 1297 C or equivalent).

§

A 22 AWG twisted pair, shielded, stranded cable (Belden 9330 or equivalent) is often required for the tamper switch. Follow
the recommendations of the manufacturer of the Host system. If the tamper input is a supervised input, the "end-of-line"
resistor may be mounted in the enclosure between TB1-4 and TB1-5.

§

The inner diameter of the cable fitting will accommodate a cable with an outer diameter of up to .260-inches.

2.7 Cable Connections
Install the cable fitting on the rear of the MaxiProx. Feed the cable through the cable fitting. Connect
the wires to the terminal strip with the minimum length necessary. Do not leave extra loops of wire
inside the Reader housing. Connect the Reader to the Host according to the terminal descriptions in
the dimension diagram. Tighten the fitting to secure the cable. Connect the drain line of the shield to
terminal TB1 Pin 2 (Power Supply Shield). If it is bare, cover it with heat shrink or tape to avoid short
circuits to the other wires. The opposite end of the drain line should be connected to the negative
terminal and the frame connection of the power supply.

CAUTION!
The shunt jumper P2 is not installed as the factory default for +24VDC operation. If the jumper is in the
+12 VDC position and +21 to +28.5 VDC is applied, circuit damage can result.

Table 1: TB1 Connector Definition
1

2

3

4

5
Tamper
Select
---

+DC

Shield Ground

Ground

Tamper
Common

Red

Drain

Black

---

Table 2: TB2 Connector Definition

1

2

3

4

5

6

7

8

9

DATA 0
DATA/TD/RX+

DATA 1
CLK/RD/RX-

DATA RTN

GREEN LED

RED LED

BEEPER

HOLD/
CARD PRESENT

TX+
RS422

TXRS422

Green

White

Orange

Brown

Yellow

Blue

Note
On TB2, pins 1, 2 and 7 have multiple purposes, depending on the interface that the Reader is
configured for. In the table above, the first description is for Wiegand, the second for Clock and Data,
the third for RS232, and the fourth is for RS422.

HID Corporation, 9292 Jeronimo Road, Irvine, CA 92618-1905, USA ? Tel: (949) 598-1600, (800) 237-7769, Fax: (949) 598-1690
http://www.hidcorp.com
MaxiProx DFM Reader Installation Manual 5375-901 Rev D
Page 7 of 20

2.8

DipSwitch and Jumper Settings

Verify the default settings according to the model ordered, or set the DIPswitches and Jumper
positions according to the following.
Table 3: DIPSwitch and Jumper Settings
Switch

Default

Description

1. Interface mode 1

On

See mode chart table 6 below

2. Interface mode 2

On

See mode chart table 6 below

3. Interface mode 3

On

See mode chart table 6 below

4. Beeper control On/Off

On

On - beep after valid card read. Off - no beep after valid card read.

5. Green LED flash

Off

O f f - flash after valid card read. On - no flash after v alid card read.

6. Single/Dual external LED

Off

O f f - single line LED control. On - dual line LED control.

7. Serial Baud 1 control

Off

See baud rate chart below.

8. Serial Baud 2 control

Off

See Baud rate chart below.

Table 4: Interface Jumpers Description - P3 and P4
P3 and P4

1-2

See mode chart table 6 below

Table 5: Switch Description - SW2
Switch

Default

Description

1. Serial Baud 3 control

On

See baud rate table 7 below

2. Note address 0

N/A

Unused

3. Note address 1

N/A

Unused

4. Note address 2

N/A

Unused

5. Note address 3

N/A

Unused

6. Note address 4

N/A

Unused

7. Unused
8. Unused

Table 6: Mode Chart
Mode

SW1-1

SW1-2

SW1-3

SW5-3

SW5-4

SW5-5

P3 & P4
Jumpe rs

Wiegand

ON

ON

ON

NA

NA

NA

1-2

Clock & Data

OFF

ON

ON

NA

NA

NA

1-2

RS232

ON

OFF

ON

NA

OFF

OFF

2-3

OFF

OFF

ON

ON

OFF

OFF

2-3

OFF

OFF

ON

OFF

OFF

OFF

2-3

RS422
terminated
RS422
unterm.

Table 7: Baud Rate Chart ? RS232 and RS422
BAUD

SW1-7

SW1-8

SW2-1

9600

ON

ON

ON

4800

OFF

ON

ON

2400

ON

OFF

ON

1200

OFF

OFF

ON

HID Corporation, 9292 Jeronimo Road, Irvine, CA 92618-1905, USA ? Tel: (949) 598-1600, (800) 237-7769, Fax: (949) 598-1690
http://www.hidcorp.com
MaxiProx DFM Reader Installation Manual 5375-901 Rev D
Page 8 of 20

Table 8: Switch Description - SW5
Switch

§

Default

Description

1. Data Isolation 1

On

See 1 below

2. Data Isolation 0

On

See 1 below

3. RS422 Terminating Resistor

On

See 5 below

4. Serial Hardware line setting 1

Off

See 6 below

5. Serial Hardware line setting 2

Off

See 7 below

1. Open Collector Data Outputs SW5-1&2 when using Wiegand or Clock & Data Interface. The data outputs may be

configured so the MaxiProx is electrically isolated from the Host pull-up resistors. The default (standard) configuration is
non-isolated outputs, switches SW5-1 & 2 are ON.
Note
When the outputs are configured as isolated, separate power supplies should be used for the
MaxiProx and Host. These switches are unused when in RS232 or RS422 mode.

§

3. Beeper Control SW1-4: The on-board beeper may be enabled or disabled. When enabled, the beeper tone is sounded
when the LED is green. SW1-4 in the ON position enables the beeper (the default).

§

2. LED Control SW1-5: The LED flash after valid card read can be controlled by both the MaxiProx and Host, or Host
only. SW1-5 in the OFF position selects flash green after valid card read (the default).

§

4. LED Mode SW1-6: Single/Dual Mode. With SW1-6 OFF (default) it is in Single Mode. The LED is normally red, until
internal or host control turns it green (only a single control line is necessary). If ON, it is in Dual Mode, and the LED is

normally off (two control lines are necessary for host control of red and green).
§

5. SW5-3 Terminating Resistor: Some RS422 connections require that the RX- line be terminated with a resistor to RX+.
If SW5-3 is in the OFF position, there is no terminating resistor on RX-. If SW5-3 is ON, then a 120-ohm resistor is

connected between RX+ and RX-.
§

6. SW5-4 Line Setting 1: SW5-4 is used to configure the Reader's interface configuration. SW5-4 should be in the OFF

position for RS232 or RS422 operation.
§

7. SW5-5 Line Setting 2: SW5-5 is used to configure the Reader's interface configuration. SW5-5 should be in the OFF

position for RS232 or RS422 operation.

2.9 Tamper Switch
Connect the tamper switch to the Host, if provided by the Host. When the cover is removed, the
tamper switch is released. The switch contacts available on TB1 Pins 4 and 5 and are either "normally
open" or "normally closed" dependent upon the position of the jumper on P1. Install the jumper to
connect pins 1 and 2 if you need the "normally open" contacts. Select the 2-3 position if you need the
"normally closed" contacts. "Normally closed" refers to the condition of the switch when the case is
open. The contacts are rated for 50 mA at 30 VDC.

2.10

Mounting

Mount the base of the MaxiProx that holds the electronics to the surface using the holes located on
the base of the Reader. There are 12 recessed holes for mounting. The holes are not through holes and
require drilling before mounting. Chose the appropriate holes to be used and drill with a 5/32 (.156) inch
bit. Use #6 screws only. (See figure 2).

HID Corporation, 9292 Jeronimo Road, Irvine, CA 92618-1905, USA ? Tel: (949) 598-1600, (800) 237-7769, Fax: (949) 598-1690
http://www.hidcorp.com
MaxiProx DFM Reader Installation Manual 5375-901 Rev D
Page 9 of 20

2.11

Power Supply

The MaxiProx Reader can be operated over the full range of 11.6-28.5VDC. Current requirements are
200-mA average and 700 mA peak at 12 VDC input. At 24 VDC (21 to 28.5 VDC) input the average
current is 260 mA and peak is 1.2 A. A linear regulated supply rated at 2.0 A is recommended. Noise
from devices such as switching power supplies, computer monitors, and arc welders can reduce the
read range or make the unit inoperable. Keep these devices at least 10 ft away from the Reader. With
the MaxiProx and power supply wired together, apply power to the Reader.

CAUTION!
The shunt jumper P2 is not installed as the factory default for +24VDC operation. If the jumper is in the
+12 VDC position and +21 to +28.5 VDC is applied, circuit damage can result.

2.12

Autotune Operation

The MaxiProx is tuned correctly when the autotune LED is green. If the LED is red, use a spacer to
position the Reader at minimum of 4 inches away from metal in the mounting surface.

2.13

Reader Testing

Apply Power to the Reader and the LED will display a sequence of flashes and beeps, indicating the
LED control mode. Two flashes of green and two beeps followed by a short delay, then one additional
flash (beep), is the correct sequence for "Green Flash/Beep on valid read? (SW1-5 off). Three initial
green flashes and beeps followed by a pause and then one additional beep indicate no Green
Flash/Beep on valid read (SW1-5 on).

2.14

Power - Up Tune

Following this initial power up sequence the Reader will perform power-up Autotune. It will beep and
turn the access LED amber for ~1 second to indicate that a power-up tune test is about to begin. It will
then attempt to tune. If it successfully tunes, it will give two quick beeps and a green on the access
and tune LED's to indicate the Reader is tuned. If unsuccessful, the unit will give a single 1.5-second
beep with a red on the access and tune LED's. If Autotune is not successful, the installer should
check for large areas of metal less than 4 inches from the back of the unit.

2.15

Periodic Autotune

Periodic Autotune retunes every 1-minute.

2.16

Supervisor Mode

During idle periods in normal operation, a periodic supervisor 1 byte transmission is sent to the host
controller over the Wiegand interface every 1 minute. Supervisor Mode is only available in Wiegand
Interface Mode.

2.17

Install Cover

Replace the top cover and top cover screw. Make sure that the autotune indicator LED remains in a
steady green state. If the LED is red, remove the cover and re-mount the unit using a non-metallic
spacer to position it further away from the mounting surface. Reinstall the cover, verify autotune, and
install the front label over the top cover screw and the autotune indicator lens.
HID Corporation, 9292 Jeronimo Road, Irvine, CA 92618-1905, USA ? Tel: (949) 598-1600, (800) 237-7769, Fax: (949) 598-1690
http://www.hidcorp.com
MaxiProx DFM Reader Installation Manual 5375-901 Rev D
Page 10 of 20

Figure 1: MaxiProx Front View

11.800
+/- .03

HID Corporation, 9292 Jeronimo Road, Irvine, CA 92618-1905, USA ? Tel: (949) 598-1600, (800) 237-7769, Fax: (949) 598-1690
http://www.hidcorp.com
MaxiProx DFM Reader Installation Manual 5375-901 Rev D
Page 11 of 20

Figure 2: MaxiProx interior view showing mounting hole locations

SW5-1 DATA 1 ISOLATION
SW2-1SERIAL BAUD 3
SW5-2 DATA 0 ISOLATION
SW2-2NODE ADDRESS
SW5-3 RS422 TERM RESISTOR
SW2-3NODE ADDRESS
SW5-4 RS 232/422 LINE 1
SW2-4NODE ADDRESS
SW5-5 RS 232/422 LINE 2
SW2-5NODE ADDRESS
SW5-6 NOT USED
SW2-6NODE ADDRESS
SW5-7 NOT USED
SW2-7NOT USED
SW5-8 NOT USED
SW2-8NOT USED

1

SW1-1INTF. MODE 1
0SW1-2INTF. MODE 2
1SW1-3INTF. MODE 3
2SW1-4BEEPER
3SW1-5LED FLASH
4SW1-6LED MODE
SW1-7SERIAL BAUD 1
SW1-8SERIAL BAUD 2

SW58 1SW28 1SW18

9
TB2
P1
1 1

3

4.000
5

2.625

TB1
1

1.64

1

3
P4
1
TB2-9
TB2-8
TB2-7
TB2-6
TB2-5
TB2-4
TB2-3
TB2-2
TB2-1
TB1-5
TB1-4
TB1-3
TB1-2
TB1-1

3
P2

3
P3
1
TXTX+
HOLD/CARD PRESENT
BEEPER
RED LED
GREEN LED
DATA RTN
DATA 1/CLK/RD/RXDATA0/DATA/TD/RX+
TAMPER SELECT
TAMPER COMMON
GROUND
SHIELD
+DC

- CAUTION -

SHUNT PINS 2 AND 3+21-28.5 VDC (DEFAULT)
SHUNT PINS 1 AND 2+11-20 VDC

1.64
2.625

4.000

- CAUTION HIGH VOLTAGE

4.000

4.000

HID Corporation, 9292 Jeronimo Road, Irvine, CA 92618-1905, USA ? Tel: (949) 598-1600, (800) 237-7769, Fax: (949) 598-1690
http://www.hidcorp.com
MaxiProx DFM Reader Installation Manual 5375-901 Rev D
Page 12 of 20

Chapter 3 Installation Notes and Guidelines
3.1 Power Supply
The recommended power supply is 12 or 24VDC, nominal, 2.0A current rating, linear regulated. The
MaxiProx cycles through varying power stages and has a peak current demand of approximately 1.2A
when in long range read mode. Average current consumption is about 260mA. Failure to provide an
adequate current capacity power supply will result in reduced read range.

CAUTION!
The shunt jumper P2 is not installed as the factory default for +24VDC operation. If the jumper is in the
+12 VDC position and +21 to +28.5 VDC is applied, circuit damage can result.

The use of a Power Switching Supply is not recommended for two reasons:
(1) This type of supply does not provide adequate response to rapid transient current loads and also
generates radio frequency (RF) interference in the same band that the Reader receives data and;
(2) The power supply may generate noise that is large enough to be transmitted or conducted to the
MaxiProx that interferes with the reception of a card signal. Some switching power supplies are not
able to provide adequate regulation to the MaxiProx Reader.

3.2 Installation near Metal
Read range will be reduced if located on metal surfaces or in the vicinity of metal objects. The amount
of reduction will be a factor of the amount of metal and the distance the Reader is from the metal. Metal
near the Reader absorbs energy from the Reader excite field and affects the signal being received from
the card by re-directing excite field transmissions into the receiver circuitry. Moving the Reader away
from the metal objects reduces energy loss.
Try to limit the amount of metallic materials installed near the MaxiProx. Use a plastic electrical box if
possible. Avoid installing conduit and other metal hardware within 2-inches of the back of the Reader
or closer than 4-inches from large metal surfaces. The typical read distance specification (24-29 inches
at 21-28.5 VDC or 21-26 inches at 12 VDC) refers to operation without metal in the vicinity of the
Reader. The read distance will be reduced if metal is installed nearby.
The MaxiProx generates a magnetic field on all sides of the Reader. Any metal that conducts electricity,
especially metal that contains iron, steel or copper will interfere with the field and reduce the effective
read range (this will happen even if the metal is behind the Reader). It helps to put a non-metallic
spacer between the Reader and the metal object.

3.3 Radio Fre quency Interference
Motors and electronic devices generate RF noise that may interfere with the reception of the signal
from a transponder. The affect of RF noise is typically a reduction of read range. The MaxiProx is
susceptible to RF interference, as are all devices that receive RF signals. The read range is affected by
the amount of interference (noise) in the area. Common sources of RF interference are power supplies,
electrical and electronic equipment, some types of lighting, computers and monitors, motors and
generators. Moving the Reader to a location known to be free of interference and testing read range
there will help to isolate RF interference as a factor in low read range situations.
HID Corporation, 9292 Jeronimo Road, Irvine, CA 92618-1905, USA ? Tel: (949) 598-1600, (800) 237-7769, Fax: (949) 598-1690
http://www.hidcorp.com
MaxiProx DFM Reader Installation Manual 5375-901 Rev D
Page 13 of 20

The MaxiProx should not be mounted within six feet of any monitors (VDTs or CRTs) because the scan
frequencies of most monitors include frequencies that may interfere with the signal received from the
access control cards.

3.4 Transponder Types
The type of transponder used affects the read range of the MaxiProx. The various styles of HID cards
and transponders use different types of antennas. The antenna type will determine the read range for
that type of transponder. The Vehicle ID tag provides the longest read range at 32-36 inches; the
ProxCard II is 24-29 inches. The IsoProx/DuoProx is 17-20 inches. The ProxKey reads at a distance of
15-17 inches.

Note
The above are recommended installation procedures. All local, state and national electrical codes have
precedence.

HID Corporation, 9292 Jeronimo Road, Irvine, CA 92618-1905, USA ? Tel: (949) 598-1600, (800) 237-7769, Fax: (949) 598-1690
http://www.hidcorp.com
MaxiProx DFM Reader Installation Manual 5375-901 Rev D
Page 14 of 20

Chapter 4 Application Notes
4.1 Wiegand Interface Description
4.1.1 Wiegand Message Format
In the Wiegand format, the ID card is programmed with a specific bit pattern and the Reader acquires
the data, checks the customer code and generally sends out the same bit pattern as previously
programmed on the card. Consult factory for variations to this method. A 26 bit Wiegand format will be
used in the examples below.
The 26 bits of transmission from the Reader to the panel consists of two parity bits and 24 code bits.
The bits are transmitted in the order described. The first bit transmitted is the first parity bit, P1; it is
even parity calculated over the first 12 code bits. The last bit transmitted is the second parity bit, P2; it
is odd parity calculated over the last 12 code bits:
Code Format

1 1
1

2

3

4

5

6

7

8

9

0

1

1

1

1

1

1

1

1

1

2

2

2

2

2

2

2

2

3

4

5

6

7

8

9

0

1

2

3

4

5

6

P1 C C C C C C C C C C C C C C C C C C C C C C C C P2
Parity Format

1 1
1

1

1

1

1

1

1

1

1

2

2

2

2

2

2

2

4

5

6

7

8

9

0

1

2

3

4

5

6

2

3

4

5

6

7

8

9

0

1

2

3

P1 E

E

E

E

E

E

E

E

E

E

E

E
O O O O O O O O O O O O P2

§ P1: First, or even parity bit
§ C : Code bits
§ P2: Second, or odd parity bit
§ E : Bits for calculation of even parity
§ O: Bits for calculation of odd parity
Data format within the 24 code bits which includes the portioning of the bit, the designation of the
Most Significant Bit (MSB) or the Least Significant Bit (LSB) shall be subject to definition by the
panel and Reader manufacturers and may remain proprietary.
4.1.2 Output Specification
The specifications of voltage, current, power and timing are from the perspective of the Reader. A
common signal ground is defined as a voltage reference that is common to both the Reader and the
control panel. The voltages for the data outputs are referenced from the power supply ground located
at the Reader. The voltage measured for the power to the Reader is referenced from the power supplyreturn connection location at the Reader, not at the source of the power.
HID Corporation, 9292 Jeronimo Road, Irvine, CA 92618-1905, USA ? Tel: (949) 598-1600, (800) 237-7769, Fax: (949) 598-1690
http://www.hidcorp.com
MaxiProx DFM Reader Installation Manual 5375-901 Rev D
Page 15 of 20

The voltage, current, and timing of the data pulses are measured at the Reader in reference to the
power supply/signal ground at the Reader. The voltage, current and timing of a signal driving an
auxiliary input device on a Reader is measured at the control panel that is controlling the input device
(with reference to the signal ground at the panel).
4.1.3 Signal Levels
The Data One, Data Zero, and LED Control conductors connect signals between the Reader and the
panel. The logic levels are defined as follows:
Table 9: Logic Levels
Voltage

Data Outputs (Data0 and Data1)

Control Inputs (LED's, Hold, Beeper)

Levels

Minimum

Maximum

Minimum

Maximum

Voh
Vol
Ioh
Iol

3.5V
0.0V
0.0mA
-25.0mA

5.5V
0.5V
5.0mA
0.0mA

3.5V
0.0V
-1.0mA
0.0mA

5.5V
0.5V
0.0mA
25.0mA

4.1.4 Data Pulses
The Data One and Data Zero signals are normally held at a logic high level until the Reader is ready
to send a data stream. The Reader places asynchronous low pulses on the appropriate data lines to
transmit the data stream to the panel. The following timing parameters shall be observed:
Figure 3: Data Pulses - Timing Parameters
Data One
Voh
Vol
Tpw

Tpw

Data Zero
Voh
Vol
Tpi

§

Tpw

§

Tpi

Tpw

Tpi

Pulse Width Time - 30uS (minimum) to 50uS (maximum)
Pulse Interval Time - 1.8mS (minimum) to 2.2mS (maximum)
4.1.5 Example Output
The following is an example of an ID card with the number of ?816? decimal, which will be output by the
MaxiProx Reader, the number ?02004CA0661? hex.

HID Corporation, 9292 Jeronimo Road, Irvine, CA 92618-1905, USA ? Tel: (949) 598-1600, (800) 237-7769, Fax: (949) 598-1690
http://www.hidcorp.com
MaxiProx DFM Reader Installation Manual 5375-901 Rev D
Page 16 of 20

Note
The customer code is never transmitted or displayed.

customer code
code
card number

sentinel parity
10 zeros
odd

bit

even

[0 0 0 0 0 0 1] [0 0 0 0 0 0 0 0 0 0] [1] [0] [0 1 1 0 0 1 0 1] [0 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0] [1]
| 0 | 2 | 0 | 0 | 4
| C | A | 0 | 6 | 6
Wiegand Output
|0 | C | A | 0 | 6 | 6
Hex code numbers
[ 6 | 5 ][ 0 | 3 | 3 | 0
Decimal conversion
[
101
][
0816

parity
facility

|
|

]
]

1 |
1|

4.2 Clock and Data Interface Description
4.2.1 Clock and Data Message Format
The Clock and Data interface consists of three signals , Card Present, Data and Strobe/Clock. The
interface is a serial data stream, which is controlled with a clock/strobe that indicates when data is
valid. All signals are quiescent high. Card Present goes low when data is about to be sent and
remains low until the whole data stream is completed. Data is the signal that determines the ?ones?
and ?zeros?. Strobe/Clock is the signal that indicates when data is valid for each cycle.
The Track 2 message format is a stream of binary bits that are grouped into HEX characters. The
message starts with leading zeros, followed by a start sentinel, data, end sentinel, LRC and trailing
zeros. Each HEX character has error correction in the form of a parity bit. Each character consists of
five bits. The maximum number of characters for a magnetic strip card encoded on Track 2 are 40, this
product will output less than 40 characters. The data consists only of BCD digits, the remaining HEX
digits, A to F, are used for the start and end sentinel, data separators and control. Only hex B and F are
used, A, C D and E are not used. The message will consist of a minimum of 210 bits.
The bits of a character are in the order 1248P , where parity is odd over the four bits. The LRC is the
Xoring of the message, starting with the start sentinel and ending with the end sentinel. The LRC does
not include the parity bits of the characters in the Xoring. LRC does include its own odd parity bit
that covers the four bits that are the result of the Xoring.
........

Customer code 0,1, 63, 72 and 73 (existing customer codes) cards will be read and output in the Track 2
format. The data on these cards will be packed into the Track 2 format in segments of three bits, so
the character does not exceed a BCD seven.
4.2.2 Data Timing
The outputs, Card Present, Data and Strobe are low going signals and the following timing chart
describes the timing.

HID Corporation, 9292 Jeronimo Road, Irvine, CA 92618-1905, USA ? Tel: (949) 598-1600, (800) 237-7769, Fax: (949) 598-1690
http://www.hidcorp.com
MaxiProx DFM Reader Installation Manual 5375-901 Rev D
Page 17 of 20

Figure 4: Data Timing - Timing Chart
card present

data

0 0 0

0 0 0 0 0
1 1 1

0 0 0 0
1 1 1 1 1

clock/
strobe

1st valid bit

bit time

strobe width

Note: the first 25 bits and trailing bits are zeros, not shown above.

§

bit time = 1.5ms (default)

§

strobe width = bit time/3 (33% of bit time), default = 500us

§

Clock/Strobe is valid 1.5ms (one clock cycle, min) after card present is asserted

§

Data is valid 10us (min) before the negative edge of clock/strobe

§

Card Present returns to the high level 50 ms (max) after the last clock/strobe.

The above timing is representative of a magnetic stripe card traveling at 8.9 inches per second. The
timing is to be adjustable for cards traveling at 4 inches per second to 20 inches per second. This
relates to bit times of 3.3 ms and 666us, respectively. There are 75 bits per inch on Track 2.
4.2.3 Output signal Levels
Inputs: low threshold = 0.8 volts

high threshold = 3.5 volts

4.2.4 Bit structure
The Reader will read an 1849 or compatible chip that is encoded with 44 bits of data. The data will be
programmed in accordance with ProxGuard formatting. The data will be packed into the ABA/ISO
Track 2 message format in accordance with the following rules based on customer code:
Case 1:

Customer Code = 0, 1, 63, 72, 73 or other, will have the data output as follows.
The output is in the Track 2 character format but the bits are packed in sets of three bits (octal):
ccc CCCC

a bcd efg hij klm nop qrs tuv wxy zAB CDE FGH IJK

Where cccCCCC is the customer code, abc...IJK is the programmed data on the card.

HID Corporation, 9292 Jeronimo Road, Irvine, CA 92618-1905, USA ? Tel: (949) 598-1600, (800) 237-7769, Fax: (949) 598-1690
http://www.hidcorp.com
MaxiProx DFM Reader Installation Manual 5375-901 Rev D
Page 18 of 20

1248p 1248p 1248p1248p 1248p1248p 1248p1248p1248p1248p 1248p1248p1248p 1248p 1248p 1248p 1248p1248p1248p
c000p Ccc0p CCC0p a000p dcb0p gfe0p jih0p mlk0p pon0p srq0p vut0p yxw0p BAz0p EDC0p HGF0p KJI0p

Case 2:

Customer Code = 74 are structured as follows:
421 8421

8421 8421 8421 8421 8421 8421 8421 8421 8421

CCC CCCC 1 aaaa bbbb cccc dddd eeee ffff gggg hhhh iiii
CCC CCCC

- Customer code

1

- fixed bit ?1?

aaaa

- Most significant nibble of message

bbbb

- Second MSN

cccc

- next nibble

hhhh

- least significant nibble of message

iiii

- LRC of nibbles aaaa to hhhh, start (B) and end sentinel (F) (xor of the nibbles or the even parity of the
respective column)

The output from the Reader will look like the following:
1248p 1248p 1248p

1248p

1248p

1248p 1248p 1248p 1248p 1248p 1248p


start data a

data b

data c data d data e

data f data g data h end LRC

The message structure follows the ISO/ABA Track 2 standard. The first character is a start sentinel: B
(hex), which is followed by data. After the data there is an end sentinel: F (hex), followed by an LRC.
The LRC is the xoring of the message in accordance to the bit position. Each character has an odd
parity bit that covers bit 1 to bit 4 of the nibble.
A typical message:

B 1 2 3 F LRC the bits broken down:
1248p 1248p 1248p 1248p 1248p 1248p
11010 10000 01000 11001 11111 00101
B

1

start <

2
data

3

F
> end

4
LRC

4.2.5 Bit Stream
HID Corporation, 9292 Jeronimo Road, Irvine, CA 92618-1905, USA ? Tel: (949) 598-1600, (800) 237-7769, Fax: (949) 598-1690
http://www.hidcorp.com
MaxiProx DFM Reader Installation Manual 5375-901 Rev D
Page 19 of 20

The bit stream will consist of 25 leading zeros, the message and fill with zeros until the end of the
message. The message will consist of a minimum of 210 bits.
Example

00000000000000000000000000 11010 10000 01000 11001 11111 00100 00000000000000...000000
B

1

2

3

F

LRC

4.2.6 Output Specification
Vol = 0.8 V
Voh = 3.5 V
sink = 25 ma
source = 5 ma

4.3 RS232 and RS422 Card Message Specification (Send
Mode Only)
When Access Cards (transponders) are presented to the MaxiProx Reader, the Reader sends a
message. The message is in the following format:
CCDDDDDDDDDDXX
^ First character sent

All characters C, D and X are ASCII encoded, hexadecimal digits. (i.e., the hex value 7 is sent as an
ASCII character 7 or the hex value E is sent as an ASCII character E ).
The CC field is reserved for use by HID Corporation. The valid values are 00 through 7F.
The DDDDDDDDDD field is the transponders (Access Card) data. The valid values are 0000000000 through
1FFFFFFFFF (ASCII).
The XX field is a computed checksum. The checksum is calculated by first grouping the message data
into the pairs CC DD DD DD DD DD. Each pair of characters represents one byte of data. Then each pair
of characters is converted from ASCII to their respective hex values. At this point, the 6 bytes are
added together. The checksum is equal to the least significant 8 bits of the result.
is the ASCII code for a carriage return. (0D hex)
is the ASCII code for a line feed. (0A hex)

For example, if the MaxiProx reads a transponder (Access Card) that contains the value CC=00 and
DDDDDDDDDD=01234ABCDE , the Reader will report the ASCII message 0001234ABCDE08.
Note that each of the characters is ASCII encoded. The actual bytes (hex value) that are sent to the
host are:

HID Corporation, 9292 Jeronimo Road, Irvine, CA 92618-1905, USA ? Tel: (949) 598-1600, (800) 237-7769, Fax: (949) 598-1690
http://www.hidcorp.com
MaxiProx DFM Reader Installation Manual 5375-901 Rev D
Page 20 of 20

The checksum was computed by adding 00 + 01 + 23 + 4A + BC + DE = 208 hex. The checksum is the least
significant 8 bits of this result or 08 hex. The communications settings are 9600-75Hz BAUD, 8 bits, 1
stop bit, no parity.

HID Corporation, 9292 Jeronimo Road, Irvine, CA 92618-1905, USA ? Tel: (949) 598-1600, (800) 237-7769, Fax: (949) 598-1690
http://www.hidcorp.com
MaxiProx DFM Reader Installation Manual 5375-901 Rev D
Page 21 of 20



MaxiProx®
Série 5375

Lecteur de cartes de proximité
Applications
Le lecteur MaxiProx de HID est le produit idéal des
installations combinant les applications de contrôle de
parking et de grandes distances de lecture. Son boîtier
esthétique et robuste, facile à installer, renferme toute
l'électronique du lecteur.

Caractéristiques
?
?

?
?

?
?
?

?

Grande distance de lecture, jusqu'à 2 m (8'') avec le
badge ProxPass®.
Sa distance de lecture ne varie pas grâce à la fonction de
réglage automatique (le lecteur étant placé à plus de
1,20 m d'une surface métallique)
Disponible avec interface Wiegand, Clock&Data et
différentes sorties série.
La fonction "Parking hold" permet la connexion à un
détecteur en boucle au sol qui assure une parfaite
détection des véhicules à l'entrée d'un parking.
Compatible avec tous les formats de cartes et étiquettes
HID jusqu'à 85 bits.
Equipé d'une LED multicolore et d'un signal sonore
(beeper) pilotés en autonome ou à distance.
Il est possible de faire fonctionner deux lecteurs
MaxiProx à un mètre l'un de l'autre, dans le cas des
installations tous trafics (poids lourds et véhicules).
Doté d'un signal de présence pour les systèmes CASIRUSCO.

Caractéristiques

Spécifications techniques

Montage: pour une distance de lecture optimale, il est
recommandé d'installer le lecteur sur une surface non
métallique.

Distance de lecture maximale*
Carte ProxCard® II: jusqu'à 73 cm (29")
Carte ISOProx® II: jusqu'à 50 cm (20")
Porte-clés ProxKey? II: jusqu'à 43 cm (17")
Carte ProxCard® Plus: jusqu'à 25 cm (13")
Carte SmartProx?: jusqu'à 43 cm (17")
ProxPass® jusqu'à 240 cm, 2,4 m (8")
* En fonction des conditions d'installation sur site

Signal sonore/visuel: lorsque vous présentez une carte de
proximité devant le lecteur, la LED rouge devient verte et un
signal sonore (beeper) est émis. La LED multicolore et le
signal sonore (beeper) peuvent aussi être commandés
séparemment par le système central.
Diagnostics: lorsque le lecteur est sous tension, un
programme interne d'auto-test contrôle et vérifie la
configuration, détermine si la LED et le signal sonore
(beeper) sont commandés de manière interne ou externe et
initialise le lecteur.
Montage en intérieur / extérieur: scellé dans un boîtier en
polycarbonate, robuste et résistant aux intempéries, au
vandalisme et aux environnements hostiles, il est fiable aussi
bien en intérieur qu'en extérieur.
Interfaçage aisé: peut être connecté à tous les systèmes de
contrôle d'accès existants fonctionnant sous protocole
Wiegand, Clock&Data, RS-232 et RS-485. Les interfaces
séries supportent les fréquences de 1200, 2400, 4800 et 9600
bauds.
Sécurité: il est équipé d'un contact d'autoprotection du
boîtier émettant un signal électronique en cas de tentative
d'effraction du lecteur. Reconnaît les formats de cartes
jusqu'à 84 bits.
Garantie: garantie à vie contre tout défauts matériels ou
vices de fabrication. (Pour de plus amples détails, veuillez
consulter nos conditions générales de garantie).
Options:
? Fonctionnement avec LED et signal sonore
? Etiquette personnalisée
(Veuillez consulter le guide de commande HID, dans lequel
vous trouverez une description des options ainsi que les
numéros de référence correspondants).

29.97 cm
(11.80")

2.54 cm
(1.00")

Dimensions:
30,0 x 30,0 x 2,54 cm (11.8" x 11.8" x 1.0")
Materiau: polycarbonate UL 94
Alimentation: Configurable en 12 ou 24 V cc.
Alimentations linéaires recommandées.
Tensions requises:
12 V cc: moyenne 200 mA, maximale 700 mA
24 V cc: moyenne 260 mA, maximale 1,2 A
Température de fonctionnement:
De -30 °C à +65 °C (-22 °F à +150 °F)
Humidité de fonctionnement:
Humidité relative de 0 à 95% sans condensation
Poids: 1,4 kg (51 oz.)
Numéro de référence:
N° de référence standard : 5375
Description : interface Wiegand, gris fonçé, LED tricolore,
signal sonore (beeper) intégré
Fréquence de transmission: 125 kHz
Homologations: Homologation Canada/UL 294: Systèmes de
contrôle d'accès
Homologation FCC, Etats-unis
Homologation Canada
Marquage CE, 15 pays de l'Union Européenne d'après la
Directive R&TTE (EN60950 - ITE Sécurité Electrique, EN 300
330 - SRD, et ETS 300 683 - EMC)
IEC60950, ITE CB Plan de Sécurité Electrique
Marquage C-Tick Australie
EMC (Compatibilité électromagnétique) Nouvelle Zélande
Distance de câblage:
Interface Wiegand: 152 m (500 pieds)
Interface Clock&Data: 15 m (50 pieds)
RS-232: 15 à 61 m (50 à 200 pieds)
Nous vous recommandons d'utiliser des câbles multibrins
ALPHA 1295 à 5 conducteurs (22 AWG - American Wire
Gauge), totalement blindés ou équivalent. D'autres
conducteurs peuvent être nécessaires pour le câblage de la
commande de la LED ou du signal sonore (beeper).
RS-422 et RS-485: 1219 m (400 pieds). Nous vous
recommandons d'utiliser un câble ALPHA 1297.
LIT5375DS 11/2003, remplace la version 4/2000

29.97 cm
(11.80")

HID CORPORATION
(CORPORATE HEADQUARTERS)
9292 Jeronimo Road
Irvine, CA 92618-1905 U.S.A.
Phone +1 (949) 598-1600 or (800) 237-7769
Fax +1 (949) 598-1690

www.HIDCorp.com/francais

HID CORPORATION LTD
35 Bd de la Victoire
67000 Strasbourg
France
Tél. : +33 (0)3 90 22 10 66
Fax : +33 (0)3 88 36 64 45